Technical data

64
Siemens Building Technologies
Fire Safety & Security Products 08.2006
Operation User action Notes
is not set to KEYBOARD.
Recall Preset [n] [PRESET] Range 1-89.Preset 95* or Preset 2* twice within 2 seconds functions
as the OSD Mode 'MENU' command. When in OSD mode Preset 1
switches the joystick between cursor and camera control. When in
OSD cursor mode Preset 3 operates as SET.
Store Preset [n] hold [PRESET] Range 1-89.
Run Pattern [PATTERN]
Enter OSD Menu Mode [9] [5] [PRESET] or [2]
[PRESET] [2] [PRESET] within
2 seconds.
Recall Preset 95* or Recall Preset 2* twice within 2 seconds
functions as the OSD Mode 'MENU' command.
Navigate OSD Menu Mode Joystick for
Up/Down/Left/Right.[3]
[PRESET] for Set.
When in OSD mode Recall Preset 1 switches the joystick between
cursor and camera control. When in OSD cursor mode Recall
Preset 3 operates as SET
* The presets used to access the OSD are programmable via the XTU.
12.5.2 Ernitec ERNA protocol
NOTE
RS485 connection; 2400 baud, no parity, 8 data bits, 1 stop bit.
Camera addressing is 0-254 for cameras 1-255. Also responds to broadcast address 255.
Tested using Ernitec Keyboard 1503M.
Operation User action Notes
Pan / Tilt /Zoom / Focus Joystick for Pan/Tilt/Zoom,[FN] / [FF]
for Focus
When in OSD cursor mode Pan / Tilt operate as cursor right / left /
up / down (but see also Recall Preset 1 below).
Iris [OPEN] / [CLOSE] Only operates when exposure priority is set to KEYBOARD.
AutoIris On [AUTO] [OPEN] or [AUTO] [CLOSE] Overridden automatically on a manual iris operation.
AutoFocus On [AUTO] then either [FN] or [FF]
AutoFocus Off [FN] or [FF] Manual control overrides autofocus.
Night Mode [4] [AUX ON] Activates Auxiliary 4 function. Switches camera to night mode
(colour/mono version only).
Day Mode [4] [AUX OFF] Deactivates Auxiliary 4 function. Switches camera to day mode
(colour/mono version only).
One-Touch White Balance [IC] If one-touch white balance is enabled in OSD and exposure priority
is not set to KEYBOARD.
Recall Preset [n] [PRESET] Range 1-99. Preset 95* or Preset 2* twice within 2 seconds
functions as the OSD Mode 'MENU' command. When in OSD mode
Preset 1 switches the joystick between cursor and camera control.
When in OSD cursor mode Preset 3 operates as SET.
Start Preset Sequence [PRESET SEQUENCE] Starts Tour 1.
Save Preset [n] [ESC] [PRESET] Range 1-99.
Insert Preset into Stack [n] [SHIFT]+[INS] Appends specified preset to end of current tour if possible**. Speed
= 100%, Dwell = currently selected dwell.
Delete Preset from Stack [n][SHIFT]+[DEL] Deletes the last occurrence of the specified preset from the tour** (if
present) and moves the presets above it down by one position.
Leaves any other occurrences of the same preset in the tour intact.
Clear Stack [ESC] [AUX OFF] Clears the tour**.
Sequence Dwell Time [n] [TIME] Sets the dwell time used by the next Insert Preset into Stack
command*.
Enter OSD Menu Mode [9] [5] [PRESET] or[2] [PRESET] [2]
[PRESET] within 2 seconds
Recall Preset 95* or Recall Preset 2* twice within 2 seconds
functions as the OSD Mode 'MENU' command.
Navigate OSD Menu Mode Joystick for Up/Down/Left/Right.[3]
[PRESET] for Set.
When in OSD mode Recall Preset 1 switches the joystick between
cursor and camera control. When in OSD cursor mode Recall
Preset 3 operates as SET.
* The presets used to access the OSD are programmable via the XTU.
** It is recommended that the OSD is used to setup a Tour.