GSM REMOTE SUPERVISION GB 051 Set for cellular phone Siemens C35i, M35 or S35 Automatic Information Transfer over the GSM Network USER GUIDE LEVEL
Dear Customers, We would like to congratulate you on purchasing our product – GSM Remote Supervision GB 051. This way you are getting a high-class and technically highly modern product. GSM Remote Supervision GB 051 allows first-class and highly effective protection of cars or properties. It provides protection which cannot be easily disabled by cutting the phone line, protection which sends an ALARM message within 3 seconds and which allows also continuous control of protected area.
TABLE OF CONTENTS – GSM Remote Supervision GB 051 1. Product Description................................ ................................ ........................ 4 1.2. Contents of Delivery ................................ ................................ ............... 5 2. Safety Commands ................................ ................................ ......................... 5 3. Installation and Setting into Operation................................ ............................ 6 3.1.
1. Product Description 1.1. Description of Function GSM Remote Supervision GB 051 consists of plastic box, which is firmly joined to the battery of cell phone. Communication cable with connector gets out of this box into cell phone, which is used by GB 051 for realization of phone connection and reception and sending of SMS messages.
1.2.
! 3. The GB 051 unit must be stocked always with the mobile phone connector disconnected – when disconnected from external power supply, the GB 051 is supplied from the mobile phone battery and the battery can be damaged by getting completely flat. Installation and Setting into Operation 3.1. Assembly of GSM Remote Supervision GSM Remote Supervision by LEVEL is designed for operation in dry places.
RESET INIT By connection clips no. 2 and 3 (ground and reset) the unit reset will be run, while all the set configuration value will remain in place. The value of days in service will be set to 0. Detailed description of how to carry on the initialization can be found in Chapter 4.1. The GSM Remote Control device will be set into default manufacturer’s settings by the initialization.
Cell phone must be in basic configuration, only parameters specified further can be changed. A SIM card inserted in the GB 051 device must be configured in one of the two ways described below: a) If SIM is not blocked by PIN code, then the PIN value in GB 051 is irrelevant – in this case you can skip this instruction and continue to assembly the GB 051 and the cell phone. b) If SIM is blocked by PIN, and then the PIN in GB 051 must be the same with the PIN at the SIM in mobile phone.
If the PIN code on the SIM card is the same as the PIN in GB 051 and SIM is blocked by PIN, then after setting new PIN to the GB 051 unit the PIN will be changed in both – the SIM and GB 051 unit. GB 051 replies to this SMS message and draws sender’s attention to necessity of unification of PIN in Remote Supervision and phone and to necessity of switch-off of cell phone. After reception of this SMS message verify correct PIN code change by switching the phone off with the red phone button.
Send a control SMS message from cell phone or Internet, which includes in text: XXppppINSTRUCTIONVparameter XX Two capital letters X pppp Four digits of current PIN in GSM Remote Supervision INSTRUCTION Key word of the command (no difference with capital or small letters) V Space follows parameter Set-up value* End of sequence by space or end of SMS message One SMS can include up to 4 commands.
Value of PIN of GSM gate set from production and after initialization is 0000. PIN 0000 shall not be set into cell phone from gate so that blockage of phone is not caused during first contacts with gate. Example: Original PIN of GSM gate is 0000. SIM card, which you use in cell phone in GSM gate has PIN 1234 and is blocked by PIN. Insert the SIM card into the mobile phone, but do not connect the GB 051 connector yet. Insert the required PIN in the mobile phone (e.g. 1234).
4.3. INIT – Re-initialization of Values Set from Production In case you lost view of GB 051 set-up you can carry out remote re-initialization of parameter values set in production. Command Pppp XXppppINIT Four digits of current PIN GSM Remote Supervision will be set to initial set-up from production. Sender of Command receives message about correct reception of Command.
Command Pppp Number XXppppMCALLVnumber *1) Four digits of current PIN Maximum 14 digits of number of any phone *2) *1) The space is between key word of command „MCALL“ and value of parameter „h“ *2) Number can be entered in national format – e.g. 606445566 but also in international format – e.g. +420606445566. No number is activated from production. After entering this parameter GB 051 calls set number once a month in order to spend at least one tariff impulse.
If you want to deactivate this function set command without parameter – tm. XXppppINFOSMS without further parameters. 4.8. SMSINT – Interval for Dispatch of SMS Messages about Operation Interval for sending regular SMS messages to INFOSMS number, which include time of operation, can be set: Command XXppppSMSINTVn (interval of one day is set from production) pppp Number Four digits of current PIN Number from 1 to 30. It is interval for sending successive message about operation.
Command *1) XXppppSMSNOA1Vnumber XXppppSMSNOB1Vnumber XXppppSMSNOA2Vnumber XXppppSMSNOB2Vnumber XXppppSMSNOA3Vnumber XXppppSMSNOB3Vnumber XXppppSMSNOA4Vnumber XXppppSMSNOB4Vnumber XXppppSMSNOA5Vnumber XXppppSMSNOB5Vnumber XXppppSMSNOA6Vnumber XXppppSMSNOB6Vnumber XXppppSMSNOB7Vnumber XXppppSMSNOB7Vnumber XXppppSMSNOB8Vnumber XXppppSMSNOB8Vnumber pppp Number *2) *1) *2) Activated by input Order on the No.
If you only want to change value of output regardless of previous state send command without parameter “y” – e.g. XXppppOUT5 changes value of output No. 5 to reverse. Newly set actual values of all 8 inputs/outputs are sent back to sender and to INFOSMS number. 4.11. LIST – Detection of Set-up If you want to find out which values of parameters are set in GB 051 it is possible to send control SMS message, which initiates sending messages with detailed description of set-up back to sender.
The call will take 255 seconds unless you end it sooner by hang-up. Sensitivity of cell phone built-in microphone might be relatively low. Therefore it is necessary to select a suitable placement of the unit in order to use this feature. 5. Programming from PC Comfortable way of setting of all GB 051 parameters from PC by the means of configuration program and serial cable with converter can be used. Program and cable can be bought additionally as set for configuration from PC – supply No. ED 051 011.
7.
8. Basic Technical Parameters GB 051 ALARM tone Inputs of SMS messages No. 1–8 Logical 0 Logical 1 Outputs of SMS messages No. 1–8 Logical 0 Logical 1 GSM network GSM SIM card Device Power supply voltage Peak power consumption during charging Max. time of charging Power consumption with charged battery Time of operation from backup battery Size Weight Operational temperatures 19 400 Hz 0–0,5 V 4–6 V max.
GUARANTEE CERTIFICATE Product name: ..........…....................... Type: …….....…………....................……….. Production number: .…...................…. Date of sale: .............…………........……….. Signature: …………….............………. Seller (stamp): ……………………………….. Information about guarantee repairs: Date of receipt Date of return Signature Description of defect Producer: LEVEL ltd., Plhovská 1997, 547 01 Náchod. Czech Rep. Tel/Fax No.: +420 491-44 66 11. e-mail: level@levelna.cz, www.levelna.
GUARANTEE CONDITIONS Length of guarantee period is 24 months from the date of sale. Guarantee applies only to goods registered or identified by company LEVEL. Guarantee repair will be carried out at latest within 10 working days after receipt of defective goods by company LEVEL provided that spare part is disposable in store. If it is not possible alternative solution will be offered to user for time of repair. Guarantee repairs will be carried out in company seat.
STATEMENT OF CONSENSUS We, LEVEL Ltd.., Plhovská 1997, 547 01 Náchod, Registration No.: 47469374, V.A.T. No.: 243-47469374, declare hereby our exclusive responsibility that hereinafter mentioned product meets requirements of technical regulations, that product is save when used on specified conditions and that we took all actions, which ensure consensus of all products of hereinafter mentioned type placed on the market with technical documentation and with requirements of relevant government regulation.
GB 051@1.02 © LEVEL, 2003 LEVEL Ltd, Plhovská 1997, Náchod 547 01 CZECH REPUBLIC E-mail level@levelna.cz www.levelna.
