s C2-010/C2-010-I ADSL2+ Router User’s Manual Rev: 1.3 2005/1210 No part of this publication may be reproduced in any form by any means without the prior written permission. Other trademarks or brand names mentioned herein are trademarks or registered trademarks of their respective companies. This manual currently suits for C2-010/C2-010-I.
C2-010 / C2-010-I ADSL2+ Router User’s Guide Contents 1.1 Device Introduction....................................................................................................................... 1-1 1.2 Features........................................................................................................................................ 1-1 2.1 Packing List ..................................................................................................................................
C2-010 / C2-010-I ADSL2+ Router User’s Guide 6.3 Save ADSL2+ Router Configuration Settings............................................................................... 6-2 6.4 Restore Factory Default Settings.................................................................................................. 6-3 6.5 Save Configuration File to PC ...................................................................................................... 6-3 6.6 Load Saved Configuration Files ................
C2-010 / C2-010-I ADSL2+ Router User’s Guide 1. Overview The ADSL2+ Router provides integrated voice and data services over ADSL “Asymmetrical Digital Subscriber Loop” WAN (Wide Area Network) connection. 1.1 Device Introduction The ADSL2+ Router is designed to provide a simple and cost-effective ADSL Internet connection for individual computers through the Ethernet ports, or use it to bridge your Ethernet LAN to the Internet.
C2-010 / C2-010-I ADSL2+ Router User’s Guide 2. Installation Planning Before installing the ADSL2+ Router, you should gather information and equipment needed to install the device, then Install the hardware as instructed, connect the cables to the device and power on the ADSL2+ Router. Prior to accessing the web-based software built into the ADSL2+ Router, you should check the IP settings on your computer and change them if necessary. 2.
C2-010 / C2-010-I ADSL2+ Router User’s Guide 2.2.2 Rear Panel ADSL port − Connect to the ADSL line Ethernet port − to your PC’s Ethernet port Power input − Connect power adapter here Factory Reset Button Figure 2-2 Rear Panel 2.3 Cable Connections After verifying proper environmental conditions such as temperature, humidity and power supply, users may start the cable connections as following. 2.3.
ADSL2+ Router User’s Guide 2.3.3 Computer to ADSL2+ Router Connection Cat 5 Ethernet Cable Figure 2-3 Computer to ADSL2+ Router Connection You can connect the ADSL2+ Router directly to a 10/100BASE-TX Ethernet adapter card (NIC) installed on a PC using the Ethernet cable provided as shown in this diagram.
C2-010 / C2-010-I ADSL2+ Router User’s Guide 2.3.4 Hub or Switch to ADSL2+ Router Connection Connect the ADSL2+ Router to an uplink port on an Ethernet hub or switch with a straight-through cable as shown in the diagram below: Figure2-5 Hub/Switch to ADSL2+ Router Connection If you wish to reserve the uplink port on the switch or hub for another device, connect to any on the other MDI-X ports (1x, 2x, etc.) with a crossed cable. 2.
C2-010 / C2-010-I ADSL2+ Router User’s Guide 3. Before Configuring ADSL2+ Router The factory default settings of ADSL2+ Router optimized all functions so as to enable it to operate on most network conditions. Usually, for the users with simple network topology, the default settings can meet the basic requirements and don’t need to change.
C2-010 / C2-010-I ADSL2+ Router User’s Guide 3.4 First Time Log on After inputting the forgoing IP address on URL address bar, a new window appears prompting you for a user name and password needed to gain access the web configuration manager. Figure 3-1. Log On Interface Use the default system user name: admin and password: admin for first time set up. You can change the password once you have established the ADSL connection.
C2-010 / C2-010-I ADSL2+ Router User’s Guide 4. Web-based Management 4.1 Summary When you successfully login the Basic directory will display the ADSL2+ Router’s current connection status − both for the WAN (Internet) and LAN (your home network) connections, as shown below. You can begin the process of configuring your ADSL modem/ADSL2+ Router by clicking on the Advanced button in the upper left-hand corner of the first Web page displayed. This will open the Wizard page, as shown below.
C2-010 / C2-010-I ADSL2+ Router User’s Guide Each tab displays menu buttons located in the left hand panel of the web interface. The table below lists the menus for each directory in the web manager. Directory Configuration and Read-only Menus Home Click the Home tab to access the Summary, WAN, DHCP, DNS, and LAN Configuration menus. Advanced Click the Advanced tab to access the Virtual Server, Application, Filter, Firewall, NAT, DDNS, and RIP menus.
ADSL2+ Router User’s Guide Figure 4-3 WAN Current Settings Menu Select the connection type used for your account. The menu will display settings that are appropriate for the connection type you select. Follow the instruction below according to the type of connection you select in the WAN Settings menu. Your Internet Service Provider (ISP) should provide the information you need to select the proper connection type.
C2-010 / C2-010-I ADSL2+ Router User’s Guide 4.2.1 Configuring a Bridged Connection for the WAN A bridged connection between your ISP and your LAN (the computers in your house or office) is the simplest type of connection possible. The ADSL2+ Router will simply convert the incoming and outgoing packets to the correct format for each side of the connection (Ethernet for the LAN, ATM for the WAN).
ADSL2+ Router User’s Guide 4. When you are satisfied that all the WAN settings are configured correctly, click on the Apply button. Note: Some accounts use PPP connection software for their Internet service connection. If you have been given a CD with PPP connection software, install this now as instructed by your service provider. After the ADSL2+ Router has rebooted it will negotiate the ADSL connection. Use the connection software to log on to the ISP network and access the Internet. 4.2.
C2-010 / C2-010-I ADSL2+ Router User’s Guide 3. Under the Static IP heading, choose the Connection Type from the pull-down menu. This defines both the connection type and encapsulation method used for your ADSL service. The available options are Bridged IP LLC, Bridged IP VC-MUX, Routed IP LLC, Routed IP VC-MUX or IPoA.. If have not been provided specific information for the Connection Type setting, leave the default setting. 4.
ADSL2+ Router User’s Guide Route NAT Enabled/Disabled − this enables or disables NAT (Network Address Translation) on the router. This should normally be enabled. IGMP Enabled/Disabled − this enables or disables IGMP (Internet Group Management Protocol) on the router. This should normally be enabled.
C2-010 / C2-010-I ADSL2+ Router User’s Guide 4.2.3 Dynamic IP Address Connection for WAN A Dynamic IP Address connection configures the Router to automatically obtain its global IP address from a DHCP server on the ISP’s network. The service provider assigns a global IP address from a pool of addresses available to the service provider. Typically the IP address assigned has a long lease time, so it will likely be the same address each time the Router requests an IP address.
ADSL2+ Router User’s Guide 5. NAT should remain enabled. If you disable NAT, you not be able to use more than one computer for Internet connections. NAT is enabled and disabled system-wide, therefore if you are using multiple virtual connections, NAT will disabled on all connections. 6. The Firewall should remain enabled for most users. If you choose to disable this you will not be able to use the features configured in the Firewall and Filters menus located in the Advanced directory.
C2-010 / C2-010-I ADSL2+ Router User’s Guide 4.2.4 PPPoE and PPPoA Connection for WAN Follow the instructions below to configure the Router to use a PPPoE or PPPoA for the Internet connection. Make sure you have all the necessary information before you configure the WAN connection. Figure 4-7 WAN Settings Menu – PPPoE/PPPoA 1. Under the ATM Interface settings at the top of the menu (including VPI, VCI, and Virtual Circuit) should not be changed unless you have been instructed to change them.
ADSL2+ Router User’s Guide 7. NAT should remain enabled. If you disable NAT, you not be able to use more than one computer for Internet connections. NAT is enabled and disabled system-wide, therefore if you are using multiple virtual connections, NAT will disabled on all connections. 8. The Firewall should remain enabled for most users. If you choose to disable this you will not be able to use the features configured in the Firewall and Filters menus located in the Advanced directory.
C2-010 / C2-010-I ADSL2+ Router User’s Guide 4.3 DHCP Configuration To display the DHCP Server menu, click the DHCP button in the Home directory. Active DHCP Clients appear listed in the DHCP Client Table below the configuration menu. Information about DHCP clients includes the IP address, MAC address, host name and lease time are displayed in the list. Figure 4-8.
ADSL2+ Router User’s Guide 4.3.3 Disabling the DHCP Server To disable DHCP, click to select the No DHCP radio button and click on the Apply button. 4.4 DNS Server Setting The ADSL2+ Router is configured by default to forward the DNS server address you enter in the DNS page, shown below, to all DHCP clients on your LAN. When DNS is enabled, the DNS clients on the LAN will automatically get DNS settings relayed from the ADSL2+ Router as they are entered here.
C2-010 / C2-010-I ADSL2+ Router User’s Guide So, if you want to use an IP addressing scheme that is different from the 192.168.1.x/255.255.255.0 scheme, you will need to give the ADSL2+ Router ADSL router a new IP address. This is done on the LAN Settings page, as shown below. To access the LAN Settings menu, click the LAN button in the Home directory. Figure 4-10. Configure LAN IP settings To change the LAN IP Address or Subnet Mask, type in the desired values and click the Apply button.
C2-010 / C2-010-I ADSL2+ Router User’s Guide 5. Advanced Configuration This chapter introduces and describes the management features that have not been presented in the previous chapter. These include the more advanced features used for network management and security as well as administrative tools to manage the ADSL2+ Router, view statistics and other information used to examine performance and for troubleshooting.
C2-010 / C2-010-I ADSL2+ Router User’s Guide expose it under insecurity risk; thus suggest not use this option unless no other alternatives. DDNS This page allows you to configure the ADSL2+ Router to use the DYNAMIC Domain Name Service (Dynamic DNS), if you have a previously established account. RIP This allows you to enable or disable the Routing Information Protocol (RIP) on PVC’s that allow routing. 5.
ADSL2+ Router User’s Guide 5.2 Virtual Server Configuration To view the following window, click on the Advanced tab at the top of the window and then click the Virtual Server button to the left. The Virtual Server will allow remote users access to various services outside of their LAN through a public IP address, such as FTP (File Transfer Protocol) or HTTPS (Secure Web).
C2-010 / C2-010-I ADSL2+ Router User’s Guide circumstances. Destination Port Enter the port number of the device on the WAN side of the network that will be accessing the Virtual Server currently being configured. Commonly, this port number is identical to the Private Port number. Existing Virtual Servers listed already have their well-known port number listed yet this may need to be changed in certain circumstances. You can specify a range of ports, a single port, save ports, or any port.
ADSL2+ Router User’s Guide 5.4 Outbound IP Filter Configuration Packet filtering is a basic security measure that should be used on any network that is exposed to a security risk. A packet filter system examines data packets and scrutinizes them in order to control network access. Filtering rules determine whether packets are passed through the Router from either side of the gateway. The rules are created and controlled by the network administrator and can be precisely defined.
C2-010 / C2-010-I ADSL2+ Router User’s Guide Filter Settings Description Src IP Address Select Any IP, Single IP, or IP Range from the drop-down menu and then enter the appropriate IP address or addresses that will be the source of packets this filter will act upon. Dest IP Address Select Any IP, Single IP, or IP Range from the drop-down menu and then enter the appropriate IP address or addresses that will be the destination of packets this filter will act upon.
ADSL2+ Router User’s Guide Filter Settings Description Src IP Address Select Any IP, Single IP, or IP Range from the drop-down menu and then enter the appropriate IP address or addresses that will be the source of packets this filter will act upon. Dest IP Address Select Any IP, Single IP, or IP Range from the drop-down menu and then enter the appropriate IP address or addresses that will be the destination of packets this filter will act upon.
C2-010 / C2-010-I ADSL2+ Router User’s Guide 5.6 Firewall This Router comes equipped with a firewall. The Firewall configuration screen allows the Router to enforce specific predefined policies intended to protect against certain common types of attacks. To configure the Router’s firewall, click the Advanced tab at the top of the screen and then the Firewall tab to the left. Figure 5-7.
ADSL2+ Router User’s Guide The Service Filtering options allow you to block FTP, Telnet response, Pings, etc, from the external network. Check the category you want to block to enable filtering of that type of packet. When you have selected the desired Firewall policies, click the Apply button to enforce the policies. 5.7 DMZ Click on the DMZ menu button to display the DMZ menu.
C2-010 / C2-010-I ADSL2+ Router User’s Guide 5.8 RIP Figure 5-9. RIP menu RIP can be enabled on any existing WAN or LAN interfaces. It may be specified to receive RIP requests and reply to them, it can be specified to send RIP queries, or to both receive and send RIP packets. Furthermore, the RIP version can be specified. The table below lists the parameters that can be specified for the pull-down RIP menus. Click the Apply button to setup RIP as specified. Current RIP configurations cannot be edited.
ADSL2+ Router User’s Guide 5.9 PPP When the WAN connection is configured for either PPPoA or PPPoE, you can configure the Router’s PPP session to remain on all the time, or to disconnect after some period of no activity. You may also choose to instruct the Router to connect each time you want to access the WAN or the Internet. Figure 5-10. PPP menu If you want the Internet or WAN connection to be available any time a host on your LAN requests access, select the Always On option.
C2-010 / C2-010-I ADSL2+ Router User’s Guide 5.10 ADSL The ADSL Configuration page allows the user to set the configuration for ADSL protocols. For most ADSL accounts the default settings Multi-mode will work. This configuration works with all ADSL implementations. If you have been given instructions to change the Modulation method used, select the desired option T1.413, G.dmt, or G.lite and click the Apply button. Figure 5-11.
ADSL2+ Router User’s Guide 5.11 ATM VCC The ATM Virtual Circuit connection menu is used to configure the WAN connection. If you are using multiple PVCs, you can change the configuration of any PVC in this menu. To create new or additional PVCs, read the section below on Multiple PVCs. This menu can be used as an alternative menu to configure the same settings found on the WAN menu in the Home directory. Figure 5-12.
C2-010 / C2-010-I ADSL2+ Router User’s Guide 6. Tools Click the Tools tab to reveal the menu buttons for various functions located in this directory. These menus are used to change the system password used to access the web manager, to save or load ADSL2+ Router configuration settings, upgrade the device firmware, save current configuration settings, restore default settings, and to perform miscellaneous actions such performing Ping tests. These menus are described below. 6.
C2-010 / C2-010-I ADSL2+ Router User’s Guide 6.2 Configure System Time Use the Time menu to configure the ADSL2+ Router’s system time manually or from an SNTP server or your computer’s system clock. Figure 6-2. Time Settings Menu If you opt to use the Automatic option you must have an IP address of an available SNTP server. Date settings use the format Year/Month/Date, Time settings use the format Hour (24 hour clock)/ Minute/ Second. Click the Apply to set the Date and Time settings. 6.
ADSL2+ Router User’s Guide 6.4 Restore Factory Default Settings To reset the ADSL2+ Router to its factory default settings, click the Restore button. You will be prompted to confirm your decision to reset the ADSL2+ Router. The ADSL2+ Router will reboot with the factory default settings including IP settings. 6.5 Save Configuration File to PC Once you have configured the ADSL2+ Router to your satisfaction, it is a good idea to back up the configuration file to your computer.
C2-010 / C2-010-I ADSL2+ Router User’s Guide Figure 6-5. Firmware Upgrade To upgrade firmware, type in the name and path of the file or click on the Browse button to search for the file. Click the Apply button to begin copying the file. The file will load and restart the ADSL2+ Router automatically. 6.8 Test The Test menus are used to test connectivity of the Router. A Ping test may be done through the local or external interface to test connectivity to known IP addresses.
C2-010 / C2-010-I ADSL2+ Router User’s Guide 7. ADSL2+ Router Status Information Use the various read-only menus to view system information and monitor performance. 7.1 Device Info This page displays the current information for the AVA-2425S. It will display the LAN, WAN, Wireless 802.11g, NAPT Session and Disk Information statistics. If your WAN connection is set up for a Dynamic IP address then a Release button and a Renew button will be displayed.
C2-010 / C2-010-I ADSL2+ Router User’s Guide The log menu buttons in this function as follow: First Page Last Page Previous Next Clear Log Save Log Display the first page of the log. Display the last page of the log. Moves back one log page. Moves forward one log page. Clears the logs completely. Save log file to your hard drive. 7.3 Traffic Statistics The device keeps statistic of the data traffic that it handles.
ADSL2+ Router User’s Guide 7.4 ADSL Status Use the ADSL Status information and the Test page for troubleshooting the ADSL connection. Figure 7-4.
C2-010 / C2-010-I ADSL2+ Router User’s Guide 8. Attachments 8.1 Technical Specifications Hardware One ADSL port RJ-11, inner pair (pin 2,3) ADSL Standards: ANSI T1.413 Issue 2 Standard Compliance ITU G.992.1 (G.dmt) AnnexA ITU G.992.2 (G.lite) Annex A ITU G.994.1 (G.hs) ADSL2 Standards: ITU G.992.3 (G.dmt.bis) Annex A ITU G.992.4 (G.lite.bis) Annex A ADSL2+ Standards: Performance ITU G.992.5 Annex A Pass DSL Forum TR-048 Performance Criteria.
C2-010 / C2-010-I ADSL2+ Router User’s Guide Spanning Tree IEEE 802.1d Dynamic Learning Up to 1000 MAC addresses Bridged/Routed Ethernet over ATM (RFC1483/2684) Encapsulation Classical IP over ATM (RFC1577) TCP/UDP ARP IPv4 RARP ICMP IP Routing IP Routing RIP v1 (RFC 1058), RIP v2 (RFC 1389) Static DHCP Server (RFC2131) DHCP DHCP Client (RFC2131) Multiple PVC Support 8 PVCs ATM format ITU-T Rec. I.
C2-010 / C2-010-I ADSL2+ Router User’s Guide 9. Appendix A – WEEE B2C All electrical and electronic products should be disposed of separately from the municipal waste stream via designated collection facilities appointed by the government or the local authorities. The correct disposal and separate collection of your old appliance will help prevent potential negative consequences for the environment and human health.
