Operating Instructions
Table Of Contents
- 1. Siemens BT300 - Startup
- 2. Keypad of the drive
- 3. Siemens Application
- 3.1 Specific functions of the Siemens application
- 3.2 Example of control connections
- 3.3 Application - Quick setup parameter group
- 3.4 Monitor group
- 3.5 Application parameter lists
- 3.5.1 Parameter programming
- 3.5.2 Column explanations
- 3.5.3 Group 3.1: Motor settings
- 3.5.4 Group 3.2: Start/Stop setup
- 3.5.5 Group 3.3: Control reference settings
- 3.5.6 Group 3.4: Ramp & Brakes Setup
- 3.5.7 Group 3.5: I/O Configuration
- 3.5.8 Group 3.6: Fieldbus Data Mapping
- 3.5.9 Group 3.7: Prohibited Frequencies
- 3.5.10 Group 3.8: Limit supervisions
- 3.5.11 Group 3.9: Protections
- 3.5.12 Group 3.10: Automatic reset
- 3.5.13 Group 3.11: Timer functions
- 3.5.14 Group 3.12: PID-controller 1
- 3.5.15 Group 3.13: PID-controller 2
- 3.5.16 Group 3.14: Multi-pump
- 3.5.17 Group 3.16: Fire mode
- 3.5.18 Group 3.17: Application settings
- 3.6 HVAC Application - Additional parameter information
- 3.7 Application - Fault tracing
Keypad of the drive Siemens Industry, Inc. • 13
24-hour support +1-800-877-7545 (Dial 2)
2
2.2 Menu structure
2.2.1 Quick setup
The Quick Setup Menu includes the minimum set of most commonly used parameters during installation
and commissioning. You can find more detailed information on the parameters of this group in
Chapter 3.3.
2.2.2 Monitor
Multi-monitor
On the multi-monitor page, you can collect nine values that you wish to monitor.
Figure 9. Multi-monitoring page.
Change the monitored value by activating the value cell (with arrow buttons left/right) and clicking OK.
Then choose a new item on the Monitoring values list and click OK again.
Basic
The basic monitoring values are the actual values of selected parameters and signals as well as statuses
and measurements. Different applications may have different statuses and different number of monitor-
ing values.
Timer functions
Monitoring of timer functions and the Real Time Clock. See Chapter 3.4.3.
PID Controller 1
Monitoring of PID controller values. See Chapter 3.4.4 and Chapter 3.4.5.
PID Controller 2
Monitoring of PID controller values. See Chapter 3.4.4 and Chapter 3.4.5.
Multi-Pump
Monitoring of values related to the use of several drives. See Chapter 3.4.6.
Fieldbus data
Fieldbus data shown as monitor values for debugging purposes at e.g. fieldbus commissioning. See
Chapter 3.4.7.
(4)
(12)
ID: M1
STOP READY I/O
(5)
(13)
(10)
STOP READY I/O
ID: M2.1
0.0rpm
STOP READY I/O
0.00 Hz
ID25
0.00Hz
0.00A
0.00%
20.0 Hz
0.0V
0.0V 81.9°C 0.0%
ID:1 M2.1.1.1
STOP Ready I/O
0.00 Hz
10.00 Hz
0.00 rpm
0.00 A
0.00 %
0.00 %
BT11116
(13)
Main Menu
Quick Setup
Parameters
Monitor
Monitor
Multimonitor
Basic
Timer functions
Multimonitor
FreqReference
Output Freq
Motor Curre
Motor Torque
Motor Voltage
Motor Speed
Motor TemperaUnit TemperaDC-link volt
FreqReferenc
FreqReference
Output frequency
Motor Power
FreqReference
Motor Speed
Motor Current
Motor Torque