Operating Instructions
Table Of Contents
- 1. Siemens BT300 - Startup
- 2. Keypad of the drive
- 3. Siemens Application
- 3.1 Specific functions of the Siemens application
- 3.2 Example of control connections
- 3.3 Application - Quick setup parameter group
- 3.4 Monitor group
- 3.5 Application parameter lists
- 3.5.1 Parameter programming
- 3.5.2 Column explanations
- 3.5.3 Group 3.1: Motor settings
- 3.5.4 Group 3.2: Start/Stop setup
- 3.5.5 Group 3.3: Control reference settings
- 3.5.6 Group 3.4: Ramp & Brakes Setup
- 3.5.7 Group 3.5: I/O Configuration
- 3.5.8 Group 3.6: Fieldbus Data Mapping
- 3.5.9 Group 3.7: Prohibited Frequencies
- 3.5.10 Group 3.8: Limit supervisions
- 3.5.11 Group 3.9: Protections
- 3.5.12 Group 3.10: Automatic reset
- 3.5.13 Group 3.11: Timer functions
- 3.5.14 Group 3.12: PID-controller 1
- 3.5.15 Group 3.13: PID-controller 2
- 3.5.16 Group 3.14: Multi-pump
- 3.5.17 Group 3.16: Fire mode
- 3.5.18 Group 3.17: Application settings
- 3.6 HVAC Application - Additional parameter information
- 3.7 Application - Fault tracing
Siemens Application Siemens Industry, Inc. • 41
24-hour support +1-800-877-7545 (Dial 2)
3
P3.5.1.24 PID2 select setpoint DigIN Slot0.1 1048
FALSE = Setpoint 1
TRUE = Setpoint 2
P3.5.1.25 Motor 1 interlock DigIN Slot0.1 426
FALSE = Not active
TRUE = Active
P3.5.1.26 Motor 2 interlock DigIN Slot0.1 427
FALSE = Not active
TRUE = Active
P3.5.1.27 Motor 3 interlock DigIN Slot0.1 428
FALSE = Not active
TRUE = Active
P3.5.1.28 Motor 4 interlock DigIN Slot0.1 429
FALSE = Not active
TRUE = Active
P3.5.1.30 Motor potentiometer UP DigIN Slot0.1 418
FALSE = Not active
TRUE = Active (Motor potentiometer reference
INCREASES until the contact is opened)
P3.5.1.31
Motor potentiometer
DOWN
DigIN Slot0.1 417
FALSE = Not active
TRUE = Active (Motor potentiometer reference
DECREASES until the contact is opened)
P3.5.1.32 Ramp 2 selection DigIN Slot0.1 408
Used for switching between ramp 1 and 2.
OPEN = Ramp1 shape, acceleration time 1 and
deceleration time 1.
CLOSED = Ramp2 shape, acceleration time 2
and deceleration time 2.
P3.5.1.33 Fieldbus control DigIN Slot0.1 441 TRUE = Forces control place to fieldbus.
P3.5.1.34 Fire mode reverse DigIN Slot0.1 1618
Reverse command of rotation direction while run-
ning in Fire Mode. This function has no effect in
normal operation.
FALSE = Forward
TRUE = Reverse
P3.5.1.43 ResetkWhTripCounter DigIN Slot0.1 1053 Reset kWh Trip Counter
Table 29: Digital input settings.
Code Parameter Default ID Description