User Manual

ManualsBrandsSiemens ManualsDamper actuatorsHandbediengerät für VAV-Kompaktregler AST10

851

OpenAir™

Handheld tool for VAV

compact controller

AST10

Serie E

The handheld tool is used for setting and displaying the parameter values in

connection with the following types of devices:

 VAV compact controller GDB181.1E/3 and GLB181.1E/3 to series D

 VAV modular controller ASV181.1E/3 to series D

With limitations:

 VAV compact controller GDB181.1E/3 and GLB181.1E/3 as of series E

 VAV modular controller ASV181.1E/3 as of series E

 VAV compact controller KNX/PL-Link GDB181.1E/KN and GLB181.1E/KN

Ordering and delivery

When ordering, please provide the name and type reference:

Handheld tool AST10

The unit is delivered together with three separate (3-wire) connecting cables in a

solid case.

CM1N5851en

07.10.2011

Building Technologies

Summary of content (6 pages)

PAGE 1
s 5 851 OpenAir™ Handheld tool for VAV compact controller AST10 Serie E The handheld tool is used for setting and displaying the parameter values in connection with the following types of devices:  VAV compact controller GDB181.1E/3 and GLB181.1E/3 to series D  VAV modular controller ASV181.1E/3 to series D With limitations:  VAV compact controller GDB181.1E/3 and GLB181.1E/3 as of series E  VAV modular controller ASV181.1E/3 as of series E  VAV compact controller KNX/PL-Link GDB181.
PAGE 2
Note Naming conventions In the following, the designation VAV compact controller applies equally to the actual VAV compact controller G..B181.1E/.. as well as the VAV modular controller ASV181.1E/3. Mode of operation The handheld tool is powered and the communication link between unit and VAV compact controller is established via one of the enclosed 3-wire connecting cables. When power is turned on, the AST10 is ready for operation after about 5 seconds, that is, the parameters can be set and read.
PAGE 3
Mechanical design The unit is portable and has been designed for use on site. It consists of two parts: plastic housing and aluminum plate. Both are connected via a snap-on mechanism and can easily be separated. The housing accommodates an electronic circuit board, setting buttons, LCD and a connecting cable. The separate cables have a connector at one end and ferrules or a 6-or 7-pin plug at the other. All wires are color-coded and labeled (refer to "Technical data").
PAGE 4
Mounting notes When using the connecting cable with the 6-or 7-pin plug, attach the tension relief band at the cable to the VAV compact and modular controllers as shown in the following illustration. 1 2 3 4 6 5 5 1 AST10 2 GDB181.1E/3, GLB181.1E/3 3 GDB181.1E/KN, GLB181.1E/KN 4 ASV181.1E/3 5 Connector on AST10 6 Strain relief Technical data Power supply G, G0 Operating voltage Safety extra low-voltage (SELV) AC 24 V 20 %.
PAGE 5
Diagrams Connection cable with ferrules (color coded and labeled): Wiring labeling 1 2 8 Wire color Brown (BR) White (WT) Green (GR) (YC) (G0) Meaning System potential AC 24 V System zero AC 24 V Communications signal G, G0 Operating voltage AC 24 V YC Communications signal With VAV compact controller as of series B With VAV compact controller as of series A G G AC 24 V Connection diagrams Example with connecting cable 74 424 0125 0 5851G01 Internal diagram Terminal code G G0 UC/YC X X (YC)
PAGE 6
Dimensions AST10 80 Vn Vmax 187 5851M01 Vmin Y 21,2 74 424 0125 0 74 424 0126 0 74 424 0301 0 Dimensions in mm 6/6  2005 – 2011 Siemens Switzerland Ltd Siemens Building Technologies Handheld tool for VAV compact controller Subject to change CM1N5851en 07.10.