Operation Manual

12
L1a Ref - AL140/AL145 / UK / A31008-M2001-L121-1-7619 / main.fm / 15.01.2010
Standard characters
1) Space
Specifications
Recommended batteries
Nickel-metal-hydride (NiMH)
V30145-K1310-X383
(Valid at the time of going to press)
The handset is supplied with recommended
batteries.
Base station power consumption
General specifications
Questions and answers
If you have any queries about the use of your tele-
phone, visit our website at
www.gigaset.com/customercare
for 24-hour support. The table below contains a list of
common problems and possible solutions.
Service (Customer Care)
We offer you support that is fast and tailored to your
specific needs!
Our Online Support on the Internet can be reached
any time from anywhere.
www.gigaset.com/customercare
It provides you with 24/7 support for all our products.
It also provides a list of FAQs and answers plus user
guides and current software updates (if available for
the product) for you to download.
You will also find frequently asked questions and
answers in the appendix of this user guide.
For personal advice on our range of products and
assistance with repairs or guarantee/warranty claims
you can contact us on:
UK helpdesk: 0 84 53 67 08 12.
Please have your proof of purchase ready when call-
ing with regard to guarantee/warranty claims.
Replacement or repair services are not offered in
countries where our product is not sold by authorised
dealers.
1x 2x 3x 4x 5x 6x 7x 8x 9x 10x11x12x13x14x
1
1 £ $ ¥ ¤
2
a b c 2 ä á à â ã ç
I
d e f 3 ë é è ê
4
g h i 4 ï í ì î
5
j k l 5
L
m n o 6 ö ñ ó ò ô õ
M
p q r s 7 ß
N
t u v 8 ü ú ù û
O
w x y z 9 ÿ ý æ ø å
Q
. , ? ! 0 + - : ¿ ¡ " ’ ; _
P
* / ( ) < = > %
#
Abc
-->
123
123
-->
ab
c
# @ \ & §
AL140 AL145
In standby mode
– Handset in base station
– Handset outside base station
ca. 1,0 W
ca. 0,8 W
ca. 1,2 W
ca. 1,0 W
During a call ca. 1,0 W ca. 1,2 W
DECT standard is supported
GAP standard is supported
(the Gigaset handset ope-
rates only with a Gigaset
bas
e)
Range up to 300 m outdoors
up to 50 m indoors
Base station power supply 230 V ~/50 Hz
Environmental conditions
in operation
+5 °C to +45 °C, 20% to
75% relative humidity
1)
Problem Cause Solution
Nothing
appears in
the display.
The handset is not
switched on.
The batteries are
flat.
Press the end call
key
a for approx.
5 seconds or place the
handset in the base
station.
Charge or replace the
batteries.
No wireless
connection
to the base sta-
tion,
Base flashes in
the display.
The handset is out-
side the range of
the base station.
The handset is not
registered.
The base station is
not turned on.
Move the handset
closer to the base
station.
Register the handset
¢ p. 10.
Check the mains con-
nector on the base sta-
tion
¢ p. 3.
You cannot
hear a ringer/
dialling tone
from the fixed
line network.
The phone cord
supplied has not
been used or has
been replaced by a
new cord with the
wrong jack con-
nections.
Please always use the
phone cord supplied or
ensure that the
pin connections are
correct when purchas-
ing from a retailer:
3-4 assignment of
telephone leads/
EURO CTR37.
Error tone
sounds after
system PIN
prompt.
PIN forgotten.
The system PIN you
have entered is
incorrect.
Reset the system PIN to
the default 0000
¢ p. 11.
All handsets are
de-registered. All set-
tings are reset. All lists
are deleted.