Datasheet

ManualsBrandsSiemens ManualsAutomationI/O Module 8DI 28.8VDC Simatic ET 200SP 8DI

Data sheet 6ES7131-6BF01-0BA0

SIMATIC ET 200SP, Digital input module, DI 8x 24V DC Standard,

type 3 (IEC 61131), sink input, (PNP, P-reading), Packing unit: 1

piece, fits to BU-type A0, Colour Code CC01, input delay time

0,05..20ms, module diagnostics for: short-circuit of sensor supply,

wire break, supply voltage

General information

Product type designation DI 8x24 VDC ST

HW functional status From FS02

Firmware version V0.0

● FW update possible

usable BaseUnits BU type A0

Color code for module-specific color identification

plate

CC01

Product function

● I&M data

Yes; I&M0 to I&M3

Engineering with

● STEP 7 TIA Portal configurable/integrated as of

version

V14

● STEP 7 configurable/integrated as of version

V5.5 SP3 or higher

● PCS 7 configurable/integrated as of version

V8.1 SP1

● PROFIBUS as of GSD version/GSD revision

One GSD file each, Revision 3 and 5 and higher

● PROFINET as of GSD version/GSD revision

GSDML V2.3

Operating mode

● DI

Yes

6ES7131-6BF01-0BA0 Subject to change without notice

Page 1/

Summary of content (4 pages)

PAGE 1
Data sheet 6ES7131-6BF01-0BA0 SIMATIC ET 200SP, Digital input module, DI 8x 24V DC Standard, type 3 (IEC 61131), sink input, (PNP, P-reading), Packing unit: 1 piece, fits to BU-type A0, Colour Code CC01, input delay time 0,05..20ms, module diagnostics for: short-circuit of sensor supply, wire break, supply voltage General information Product type designation DI 8x24 VDC ST HW functional status From FS02 Firmware version V0.
PAGE 2
● Counter No ● Oversampling No ● MSI No Supply voltage Rated value (DC) 24 V permissible range, lower limit (DC) 19.2 V permissible range, upper limit (DC) 28.8 V Reverse polarity protection Yes Input current Current consumption, max. 50 mA; All channels are supplied from the encoder supply Encoder supply Number of outputs 8 Output voltage encoder supply, min. 19.
PAGE 3
● for signal "0" -30 to +5V ● for signal "1" +11 to +30V Input current ● for signal "1", typ. 2.5 mA Input delay (for rated value of input voltage) for standard inputs — parameterizable Yes; 0.05 / 0.1 / 0.4 / 0.8 / 1.6 / 3.2 / 12.8 / 20 ms (in each case + delay of 30 to 500 µs, depending on line length) — at "0" to "1", min. 0.05 ms — at "0" to "1", max. 20 ms — at "1" to "0", min. 0.05 ms — at "1" to "0", max. 20 ms Cable length ● shielded, max. 1 000 m ● unshielded, max.
PAGE 4
Potential separation Potential separation channels ● between the channels No ● between the channels and backplane bus Yes ● between the channels and the power supply of the electronics No Isolation Isolation tested with 707 V DC (type test) Ambient conditions Ambient temperature during operation ● horizontal installation, min. -30 °C ● horizontal installation, max. 60 °C ● vertical installation, min. -30 °C ● vertical installation, max.