EcoView Installer Tool User Guide 125-3590 2014-11-11 Building Technologies
Copyright Notice Copyright Notice Notice Document information is subject to change without notice by Siemens Industry, Inc. Companies, names, and various data used in examples are fictitious unless otherwise noted. No part of this document may be reproduced or transmitted in any form or by any means, electronic or mechanical, for any purpose, without the express written permission of Siemens Industry, Inc.
Table of Contents EcoView Installer Tool Overview........................................................................................... 4 Getting Started...................................................................................................................... 4 Logging In ............................................................................................................................. 4 The Commissioning Process ....................................................................
EcoView Installer Tool Overview Getting Started EcoView Installer Tool Overview The EcoView Installer Tool is a browser-based tool that is used to commission a new installation when an Internet connection is available at the site. Automatic Log-off If there is no user activity within 20 minutes, you are automatically logged out of the EcoView Installer Tool. When you log in again, the tool opens to the last page displayed before the automatic log-off occurred, and you can continue work at that point.
The Commissioning Process Entering the Site Information The Commissioning Process Complete the following steps to commission a site: 1. Enter Site Information [➙ 5] 2. Disable Unused Devices and Check the Local Network Signal Strength [➙ 7] 3. Assign an Owner ID [➙ 10] Entering the Site Information 1. Start typing information for any of the following in the Search field: - EcoView Touchscreen serial number - Site Name - Installation Date The EcoView Installer Tool searches for matches as you type.
The Commissioning Process Entering the Site Information Figure 2: Enter Site Information Form. Field Description Site Name Enter the name or location you use to refer to the site. Site Contact Enter the name of your main contact at the site. Time Zone Select the time zone where the site is located. NOTE: This information sets the proper Daylight Saving Time (DST) functionality for the site. Address, City, State, and Zipcode Enter the street address where the EcoView hardware is installed.
The Commissioning Process Disabling Unused Devices and Checking the Local Network Signal Strength Disabling Unused Devices and Checking the Local Network Signal Strength NOTE: The Assign Owner to Commission Site page displays when you click the Submit Device Info button. If you need to return to the Rename or Enable/Disable Devices page, click the browser Back button. NOTE: The Last Contact and RSSI values displayed on the Rename or Disable/Enable Devices page do not update automatically.
The Commissioning Process Disabling Unused Devices and Checking the Local Network Signal Strength RSSI Status Action Required POOR. Allowing a site to operate with POOR signal strength is discouraged. Reposition the device to improve the signal strength. Use the RSSI feature at the EcoView Touchscreen to evaluate the signal strength before completing the site commissioning. Figure 3: Checking Device Communication.
The Commissioning Process Disabling Unused Devices and Checking the Local Network Signal Strength 6 EcoView Multi-phase Meter Subdevices Devices that are connected to the EcoView 8 DO Module. 7 EcoView Thermostat Sub-devices Remote sensors that are connected to an EcoView Thermostat. 8 Submit Device Info Button Submit the site information to Siemens Cloud Services. Troubleshooting Communication Problems ⊳ Do the following at the EcoView Touchscreen: 1.
The Commissioning Process Assigning an Owner ID Figure 4: Device Settings/Test Tab. Assigning an Owner ID CAUTION The Owner ID cannot be changed once it has been assigned. If the wrong Owner ID is entered, call the Support Department (1 + 877-306-9400). NOTE: Once an Owner ID is assigned, the site is no longer available in the EcoView Installer Tool. Any future changes to the site must be made through EcoView Web. 1. Select the site owner from the drop-down list.
The Commissioning Process Assigning an Owner ID Figure 5: Assigning an Owner ID. 11 Siemens Industry, Inc.
Managing Your Account Managing Your Account This section outlines how to update your contact information and change your password. 1. Click Welcome ABC Installer in the upper right corner of the page. The Change Installer Profile page displays. 2. To change your contact information, replace the information in any of the available fields. 3. Do one of the following: - To change your password, enter the new password in the Password and Confirm Password fields.
Managing Your Account Figure 7: Changing Your Password. 13 Siemens Industry, Inc.
Issued by Siemens Industry, Inc. Building Technologies Division 1000 Deerfield Pkwy Buffalo Grove IL 60089 Tel. +1 847-215-1000 Document ID 125-3590 Edition 2014-11-11 © Siemens Industry, Inc., 2014 Technical specifications and availability subject to change without notice.
