Submittal Sheet

Submittal Sheet 599 Series 3-Way Ball Valves
Document No. 154-045
August 12, 2013
Page 2 Siemens Industry, Inc.
Typical Specifications
Ball valves shall have female NPT type fittings and shall
be 1/2 to 2-inch (15 to 50-mm) line and ball sizes. The
valves shall have a forged brass body, chrome-plated
brass or stainless steel ball, and EPDM O-ring seals.
Valves may contain a glass-filled polymer flow optimizer
to provide an equal percentage control characteristic.
This flow optimizer should be an integral part of the ball
assembly. Ball valves shall utilize a 90-degree rotation
for control. They shall provide automated flow control of
hot or chilled water and up to 50% glycol solution for
HVAC control applications.
Technical Data
Valve Body Rating ANSI 250/600 WOG
Static Pressure 360 psi (2482 kPa)
Maximum Operating 60 psi (414 kPa) for 1/2" to 1-1/2" valves
Differential Pressure 35 psi (345 kPa) for 2" valves
Controlled Media Water, glycol solutions to 50%
Media Temperature
1/2-inch to 1-1/4 inch 35°F to 250°F (2°C to 121°C)
1-1/2 inch and 2-inch 35°F to 230°F (2°C to 110°C)
Body Forged Brass ASTM B283
Flow Optimizer Glass-filled polymer
Ball Chrome-plated brass or stainless steel
Stem Brass or stainless steel
Ball Seals Reinforced PTFE seals with
EPDM O-rings
Stem Seals EPDM O-rings
Angle of Rotation 0 to 90°
Table 2. Product Numbers for Fail-Safe Assemblies.
Fail-Safe
Control & Actuator Prefix Code
Valve
Body
Product
Number *
Valve
Size
Inches
(mm)
Close-Off
∆P in psi
(kPa)
Flow Rate
Cv
(Kvs)
2-Position,
GMA121.1P
171E
3-Position,
GMA131.1P
171F
0 to 10 Vdc,
GMA161.1P
171G
599-10350(S)
0.4 (0.34)
171E-10350(S) 171F-10350(S) 171G-10350(S)
599-10351(S) 0.63 (0.54) 171E-10351(S) 171F-10351(S) 171G-10351(S)
599-10352(S) 1.0 (0.86) 171E-10352(S) 171F-10352(S) 171G-10352(S)
599-10353(S) 1.6 (1.4) 171E-10353(S) 171F-10353(S) 171G-10353(S)
599-10354(S) 2.5 (2.2) 171E-10354(S) 171F-10354(S) 171G-10354(S)
599-10355(S) 4 (3.5) 171E-10355(S) 171F-10355(S) 171G-10355(S)
599-10356(S) 6.3 (5.5) 171E-10356(S) 171F-10356(S) 171G-10356(S)
599-10357(S)*
1/2 (15) 200 (1379)
10 (8.6) 171E-10357(S)* 171F-10357(S)* 171G-10357(S)*
599-10358(S) 6.3 (5.5) 171E-10358(S) 171F-10358(S) 171G-10358(S)
599-10359(S) 10 (8.6) 171E-10359(S) 171F-10359(S) 171G-10359(S)
599-10360(S)*
3/4 (20) 200 (1379)
16 (14) 171E-10360(S)* 171F-10360(S)* 171G-10360(S)*
599-10361(S) 10 (8.6) 171E-10361(S) 171F-10361(S) 171G-10361(S)
599-10362(S) 16 (14) 171E-10362(S) 171F-10362(S) 171G-10362(S)
599-10363(S)*
1 (25) 200 (1379)
25 (22) 171E-10363(S)* 171F-10363(S)* 171G-10363(S)*
599-10364(S) 16 (14) 171E-10364(S) 171F-10364(S) 171G-10364(S)
599-10365(S) 25 (22) 171E-10365(S) 171F-10365(S) 171G-10365S)
599-10366(S)*
1-1/4 (32) 200 (1379)
40 (35) 171E-10366(S)* 171F-10366(S)* 171G-10366(S)*
599-10367(S) 25 (22) 171E-10367(S) 171F-10367(S) 171G-10367(S)
599-10368(S) 40 (35) 171E-10368(S) 171F-10368(S) 171G-10368(S)
599-10369(S)*
1-1/2 (40) 200 (1379)
63 (54) 171E-10369(S)* 171F-10369(S)* 171G-10369(S)*
599-10370(S)
40 (35)
171E-10370(S) 171F-10370(S) 171G-10370(S)
599-10371(S) 63 (54) 171E-10371(S) 171F-10371(S) 171G-10371(S)
599-10372(S)*
2 (50) 200 (1379)
100 (86) 171E-10372(S)* 171F-10372(S)* 171G-10372(S)*
* Denotes a full-port valve without flow optimizer insert.
S – Suffix denotes stainless steel ball and stem
NOTE: Maximum operating differential pressure = 60 psi for 1/2" to 1-1/2"; 35 psi for 2".