Installation Instructions

ManualsBrandsSiemens ManualsBuilding automationTALON Room Temperature Sensors, Analog and Digital Models, Technical Specification Sheet

Table Of Contents

CAUTION:

Document No. 540-148

August 15, 2012

TALON® Analog Room Temperature Sensor,

10K Ω Thermistor

Page 1 of 4

Product Description

These sensors work with Siemens controllers. The

sensors use a 10K ohm thermistor to detect temperature.

The effective sensing range is 55°F to 95°F (13°C to

35°C).

NOTE: Any of these sensors can be mounted on

electrical boxes, stud-type mounting brackets, or

drywall. Obtain the necessary mounting hardware

and follow the appropriate mounting procedures

for the type of installation required.

Product Numbers

TALON

Logo**

No Logo

Description

587-614B 540-661B Sensing only

587-618B 540-671B Override and setpoint

587-620CB -- Override, setpoint and

temperature display,

Celsius

587-620FB -- Override, setpoint and

temperature display,

Fahrenheit

Expected Installation Time

20 minutes

Caution Notation

CAUTION:

Equipment damage or loss of

data may occur if you do not

follow the procedures as

specified.

Item Number 540-148, Rev. CA

Required Tools

• Phillips size 1 or 2 screwdriver

• 1/16-inch Allen wrench, (Part Number 192-632,

package of 5)

• Small and medium flat-blade screwdrivers

• Medium-duty electric drill

• 3/16-inch drill bit

• 1-inch hole saw

• Hammer

• Utility knife

• Wire cutters

• Small level

• Tape measure

• Marker or pencil

If using non-preterminated cables (or if cables are

damaged), you also need:

• Room sensor connector tool (RJ-11 crimping tool)

• Room sensor connector kit

Prerequisites

• Appropriate field wiring (standard six-conductor

room sensor cables, plenum) within the maximum

wiring run length for the individual field panel or

equipment controller must be installed. The

maximum recommended length is 100-feet

(30.5 m).

• See Table 2 for cable product numbers.

• All wiring must comply with National Electric Code

(NEC) and local regulations.

Figure 1. Room Temperature Sensor

(Shows All Options).

Summary of content (4 pages)

PAGE 1
Installation Instructions Document No. 540-148 August 15, 2012 TALON® Analog Room Temperature Sensor, 10K Ω Thermistor Product Description Required Tools These sensors work with Siemens controllers. The sensors use a 10K ohm thermistor to detect temperature. The effective sensing range is 55°F to 95°F (13°C to 35°C).
PAGE 2
Installation Instructions Document No. 540-148 August 15, 2012 Mounting Information Locate the sensor: • According to design specifications and local regulations. • Where the air circulates around it freely (not in recessed areas or behind doors). • Allowing a minimum of 4 inches (102 mm) free space above and below for proper airflow, the front cover removal tool, and the computer communication cable. • Away from drafts caused by doors, windows, outside walls, air registers, pipes, return air plenums, etc.
PAGE 3
Installation Instructions Document No. 540-148 August 15, 2012 Table 1. BACnet TEC or ATEC Controller Wiring Diagram. Wire 9. 1 6 3 SASC0126R1 1 Not Used 6 TX/RX 3 Room Temp/ Setpoint, Override 4 Common 5 TX/RX 2 GND Twisted Pair Pin 4 5 2 Pair 1 Pair 2 Pair 3 1 6 3 4 5 2 Plug the terminated cable into the RJ-11 port on the back of the printed circuit board (PCB). 10. Feed the extra cable back through the hole in the rubber insulator. 11. Snap the sensor front to the sensor base plate: a.
PAGE 4
Installation Instructions Document No. 540-148 August 15, 2012 Review Table 3 to verify that you have the appropriate mounting hardware. For retrofit installations, normally follow the method used by the pre-existing device. You may need to replace existing mounting hardware. Always mount the sensor vertically. Table 3. Mounting Accessories. P/N 182-621E Description Gym Guard Kit, satin chrome 182-683 Metal (and Wood) Stud Mounting Bracket (pkg.