Installation Instructions

ManualsBrandsSiemens ManualsHVAC Replacement PartsSeries 1000 Room Temperature Sensor w/ Setpoint, Beige

Document No. 540-742

February 5, 2013

Series 1000 Room Temperature Sensors,

10KΩ Thermistor (TEC and LTEC)

Item Number 540-742+3, Rev. GA Page 1 of 4

Product Description

These sensors work with the Terminal Equipment

Controller (TEC) and L

ONMARK

compliant Terminal

Equipment Controller (LTEC). The sensors use a 10K ohm

thermistor to detect temperature. The effective sensing

range is 55°F to 95°F (13°C to 35°C).

Sensors that are compliant with

LONWORKS technology are

distinguishable by the LTEC name next to the MMI jack at

the bottom of the unit.

CAUTION:

TEC and LTEC sensors and cable assemblies

are not interchangeable.

NOTE: Either sensor can be mounted on electrical

boxes, stud-type mounting brackets, or drywall.

Obtain the necessary mounting hardware and

follow the appropriate mounting procedures for

the type of installation required.

Product Numbers

Table 1. Product Numbers and Descriptions.

Product Numbers

TEC **

TEC No

Logo

LTEC

No Logo

Description

540-660 540-661B — — Sensing only

540-670 540-671 550-184 587-554B Override and

setpoint

540-680 — 550-187 — Override,

setpoint and

temperature

display

* Product number suffixes indicate the sensor color:

A = desert beige, B = white.

** On TEC sensors only, the suffix also indicates the

display's temperature scale,

C = °C, F = °F

(for example, 540-670FA for °F, desert beige).

For LTEC, see LTEC Temperature Scale Selection.

Required Tools

• Phillips size 1 or 2 screwdriver

• 1/16-inch Allen wrench, (Part Number 192-632,

package of 5)

• Small and medium flat-blade screwdrivers

• Medium-duty electric drill

• 3/16-inch drill bit

• 1-inch hole saw

• Hammer

• Utility knife

• Wire cutters

• Small level

• Tape measure

• Marker or pencil

If using non-preterminated cables (or if cables are

damaged), you also need:

• Room sensor connector tool (RJ-11 crimping tool)

• Room sensor connector kit

Expected Installation Time

20 minutes

Prerequisites

• Appropriate field wiring (standard six-conductor room

sensor cables, plenum or non-plenum as required),

within the maximum wiring run length for the individual

field panel or equipment controller must be installed.

The maximum recommended length is 100 feet

(30.5 m).

• See

Table 4 for cable product numbers.

• All wiring must comply with National Electric Code

(NEC) and local regulations.

Figure 1. Room Temperature Sensor

(Shows All Options).

Summary of content (4 pages)

PAGE 1
Installation Instructions Document No. 540-742 February 5, 2013 Series 1000 Room Temperature Sensors, 10KΩ Thermistor (TEC and LTEC) Product Description Required Tools These sensors work with the Terminal Equipment ® Controller (TEC) and LONMARK compliant Terminal Equipment Controller (LTEC). The sensors use a 10K ohm thermistor to detect temperature. The effective sensing range is 55°F to 95°F (13°C to 35°C).
PAGE 2
Document No. 540-742 Installation Instructions February 5, 2013 Mounting Information Locate the sensor: • According to design specifications and local regulations. • Where the air circulates around it freely (not in recessed areas or behind doors). • Allowing a minimum of 4 inches (102 mm) free space above and below for proper airflow, the front cover removal tool, and the computer communication cable.
PAGE 3
Document No. 540-742 Installation Instructions February 5, 2013 Table 2. LTEC Wiring Diagram. Wire Twisted Pair LONWORKS Net LONWORKS Net Power/ Service Common Setpoint/Ovrd Room Temp 1 2 Pair 1 3 SASC0093R1 Pin Pair 2 4 5 Pair 3 6 1 2. Untie the twist tie and pull about three inches (75 mm) of the sensor cable into the space. 3. If you have a single-sensor electrical box, install the electrical box adapter plate. See Figure 6.
PAGE 4
Document No. 540-742 Installation Instructions February 5, 2013 Accessories NOTE: LTEC cables can be used with either LTEC or Table 4. Room Sensor Pre-terminated Cables. TEC Product Number LTEC Product Number Vinyl Plenum Plenum Only 540-130 540-135 or 588-100A 588-100A 540-131 540-136 or 588-100B 588-100B 540-132 540-137 or 588-100C 588-100C TEC sensors and controllers. However, LTEC cables must be used with LTEC sensors and controllers. Description 25-foot (7.