User Manual

ManualsBrandsSiemens ManualsBC - Devices for Lighting ApplicationsUniversal Dimmer N 528D01

Siemens Switzerland Ltd DS02 Update: http://www.siemens.com/gamma-td

Building Technologies Division

International Headquarters

Theilerstrasse 1a  Siemens AG 2018

CH-6300 Zug Subject to change December 2018

Gamma instabus Technical Product Information

Universal Dimmer N 528D01, 2 x 300VA , AC 230 V

5WG1 528-1DB01

Universal Dimmer for switching or dimming

of dimmable lamps

● Supports dimmable lamps including LED

● Output load up to 2 x 300 VA individually or 1 x 500 VA

● No minimum load required

● Operation mode leading or trailing edge

● Automatic load detection

● Protected for short circuit, over load and temperature with LED indication

Functions with commissioning with ETS

● Operating hours counter with threshold overrun warning

● Switching cycle counter with threshold overrun warning

● Integrated 8-bit scene control and assign of each output to up to 8 scenes

Summary of content (13 pages)

PAGE 1
Gamma instabus Technical Product Information Universal Dimmer N 528D01, 2 x 300VA , AC 230 V 5WG1 528-1DB01 Universal Dimmer for switching or dimming of dimmable lamps ● ● ● ● ● ● Supports dimmable lamps including LED Output load up to 2 x 300 VA individually or 1 x 500 VA No minimum load required Operation mode leading or trailing edge Automatic load detection Protected for short circuit, over load and temperature with LED indication Functions with commissioning with ETS ● Operating hours counter with
PAGE 2
Use The universal dimmer is a 4 MU-wide device for DIN-rail mounting with N-system dimensions. It is designed for lighting control, i.e. for switching and dimming resistive, inductive or capacitive loads ranging up to 300 VA with 230V AC, 50/60 Hz per output. The bus is connected via a bus terminal block. The device electronics are supplied via the bus voltage. Application The device can be connected with loads on two outputs or for a higher load only with one output. A minimum load is not required. Fig.
PAGE 3
Technical design Operating elements A1, A2 B1, B2 C D E F Terminals channel A, B Status LED channel A, B LED for indicating normal operating mode (LED off) or addressing mode (LED on); returns to normal operating mode automatically after receiving the physical address Learning button for switching between normal operating mode and addressing mode and for receiving the physical address Label for physical address Bus terminal block Fig.
PAGE 4
Functions with commissioning with ETS The device is configured and commissioned with Engineering Tool Software (ETS) version ETS4 or higher. With the ETS (Engineering Tool Software) the specific parameters and addresses are assigned appropriately, and downloaded into the device.
PAGE 5
Building site function The building site function provided ex-factory enables switching the building site lighting on and off via bus wall switches and actuators, even if these devices have not yet been commissioned with ETS. Behaviour on unloading the application program When the application program is unloaded with ETS the device does not function. Resetting the device to factory default settings A very long push of the programming button (> 20 s) effects a reset to factory settings.
PAGE 6
Notes Security DANGER • The device must be mounted and commissioned by an authorized electrician. • A safety disconnection of the device must be possible. • The device must not be opened. • Use only loads that allow dimming operations. • Conventional transformers may be used. If they comply with the relevant standards and contain a thermal fuse. • For planning and construction of electric installations, the relevant guidelines, regulations and standards of the respective country are to be considered.
PAGE 7
Commissioning of dimmable LED and CFL Not all LED and CFL are dimmable, because they have electronic components included. Only dimmable lamps can be dimmed properly. Lamp manufactures note this feature on lamps, on packages or in the datasheets. The maximum load also depends on operating mode, current peak. Dimmable LED CFL LED retrofit LED driver Fig.
PAGE 8
Dimming behavior With the parameter settings the dimming behavior of LED can be optimized to behavior of incandescent lamps. ● With “Minimum dimming value” and “Maximum dimming value” the range of viewable brightness changes of the LED can be adjusted. ● Some LED work properly only, if the “maximum dimming value” is set to less 100%. ● With “Start on value” some LED can be only turned on with a higher brightness value, so the LED driver gets enough power to turn on the light.
PAGE 9
Mounting The device is intended to be used for permanent interior installations in dry locations within distribution boards or small casings with DIN rail EN 60715-TH35-7.5. Mounting and connection Step 1 Step 2 Step 3 Fig. 5 Mounting and connection Dismounting Fig. 6 Dismounting Commissioning The learning button is used to switch between different operational modes. Press and hold <2 s: • Enable addressing mode. The programming LED is on.
PAGE 10
Technical data Power supply KNX bus voltage KNX bus current Rated voltage Rated current DC 24V (DC 21...30V) Typical 5 mA, max. 8 mA. 230V AC +10%/-15%, 50/60 Hz 2-channel: 2 x 1.3 A @ cosФ=1.0 1-channel: 1 x 2.2 A @ cosФ=1.
PAGE 11
Technical data Physical Specifications Housing Dimensions Mounting Weight Fire load Power loss if output is off plastic 72 x 90 x 55 mm DIN-rail EN 60715-TH35-7,5 approx. 220 g approx. 2 MJ 0.
PAGE 12
Standards Electrical Safety • Bus • Devices covers • Electromagnetic compatibility Markings CE mark • Safety extra low voltage SELV DC 24 V • EN 50428 • EN 50428 KNX EIB Complies with the EMC regulations (residential and functional buildings), low voltage regulations and RoHS Directive 12 / 13 Siemens Switzerland Ltd Building Technologies Division International Headquarters Theilerstrasse 1a CH-6300 Zug DS02  Siemens AG 2018 Subject to change Update: http://www.siemens.
PAGE 13
Dimensions Fig. 8 Dimensions Support • • • The operating instructions must be handed over to the client. A faulty device shall be returned with a Return Good Note for Service provided by the appropriate Siemens sales office. If you have further questions concerning the product, please contact our technical support. ' +49 (911) 895-7222 7 +49 (911) 895-7223 * support.automation@siemens.com www.siemens.