User Manual
Table Of Contents
- 1 Cyber security disclaimer
- 2 Preconditions of this document
- 3 System overview
- 4 Desigo workflow, tools and programming
- 4.1 Coverage of the technical process
- 4.2 Coverage of the system
- 4.3 Main tasks
- 4.4 Tools for different roles
- 4.5 Working with libraries
- 4.6 Working in parallel and subcontracting
- 4.7 Workflow for primary systems
- 4.8 Workflow for room automation classic
- 4.9 Workflow for Desigo room automation
- 4.10 Desigo Configuration Module (DCM)
- 4.11 Desigo Xworks Plus (XWP)
- 4.12 Desigo Automation Building Tool (ABT)
- 4.13 Programming in D-MAP
- 5 Control concept
- 6 Technical view
- 7 Global objects and functions
- 8 Events and COV reporting
- 9 Alarm management
- 9.1 Alarm sources
- 9.2 Alarm example
- 9.3 Effects of BACnet properties on alarm response
- 9.4 Alarm response of the function blocks
- 9.5 Alarm functions
- 9.6 Alarm management by notification class
- 9.7 Alarm routing over the network
- 9.8 Alarm queuing
- 9.9 Common alarms
- 9.10 Alarm suppression
- 9.11 Alarm message texts
- 10 Calendars and schedulers
- 11 Trending
- 12 Reports
- 13 Data storage
- 14 Network architecture
- 15 Remote access
- 16 Management platform
- 17 Desigo Control Point
- 18 Automation stations
- 19 Logical I/O blocks
- 20 Room automation
- 21 Desigo Open
- 22 System configuration
- 22.1 Technical limits and limit values
- 22.2 Maximum number of elements in a network area
- 22.3 Desigo room automation system function group limits
- 22.4 Devices
- 22.4.1 PXC..D automation stations / system controllers
- 22.4.2 LonWorks system controllers
- 22.4.3 Automation stations with LonWorks integration
- 22.4.4 PX Open integration (PXC001.D/-E.D)
- 22.4.5 PX Open integration (PXC001.D/-E.D + PXA40-RS1)
- 22.4.6 PX Open integration (PXC001.D/-E.D + PXA40-RS2)
- 22.4.7 PX KNX integration (PXC001.D/-E.D)
- 22.4.8 TX Open integration (TXI1/2/2-S.OPEN)
- 22.4.9 Number of data points on Desigo room automation stations
- 22.4.10 Number of data points for PXC3
- 22.4.11 Number of data points for DXR1
- 22.4.12 Number of data points for DXR2
- 22.4.13 PXM20 operator unit
- 22.4.14 PXM10 operator unit
- 22.4.15 Desigo Control Point
- 22.4.16 PXG3.L and PXG3.M BACnet routers
- 22.4.17 SX OPC
- 22.4.18 Desigo CC
- 22.4.19 Desigo Insight
- 22.4.20 Desigo Xworks Plus (XWP)
- 22.4.21 Desigo Automation Building Tool (ABT)
- 22.5 Applications
- 23 Compatibility
- 23.1 Desigo version compatibility definition
- 23.2 Desigo system compatibility basics
- 23.2.1 Compatibility with BACnet standard
- 23.2.2 Compatibility with operating systems
- 23.2.3 Compatibility with SQL servers
- 23.2.4 Compatibility with Microsoft Office
- 23.2.5 Compatibility with web browsers
- 23.2.6 Compatibility with ABT Go
- 23.2.7 Compatibility with VMware (virtual infrastructure)
- 23.2.8 Compatibility of software/libraries on the same PC
- 23.2.9 Hardware and firmware compatibility
- 23.2.10 Backward compatibility
- 23.2.11 Engineering compatibility
- 23.2.12 Compatibility with Desigo Configuration Module (DCM)
- 23.2.13 Compatibility with Desigo PX / Desigo room automation
- 23.2.14 Compatibility with Desigo RX tool
- 23.2.15 Compatibility with TX-I/O
- 23.2.16 Compatibility with TX Open
- 23.3 Desigo Control Point
- 23.4 Upgrading from Desigo V6.2 Update (or Update 2) to V6.2 Update 3
- 23.5 Siemens WEoF clients
- 23.6 Migration compatibility
- 23.7 Hardware requirements of Desigo software products
- 24 Desigo PXC4 and PXC5
- 25 Compatibility of Desigo V6.2 Update 3 with PXC4 and PXC5
Logical I/O blocks
General functions
19
252 | 351 CM110664en_07
Function
With a binary input object, the operating hours are determined on the basis of the ON state of [PrVal] (that
is, by measuring the time for which this value is active). For multistate blocks, you can configure how many
states are to be totalized. These are combined and added in a totalizer (the various states cannot be
evaluated individually). In contrast to the input object, the output objects of the ON state for [FbVal] is
logged (not [PrVal]) to operating hours message of the output objects.
There are two separate totalizers for runtime totalization:
● Runtime totalizer
● Overall runtime totalizer
Release
Runtime totalization can be enabled via the [EnOph] pin (Enable operating hours count). This is a binary
value for binary objects, for multistate objects a list of values released for counting.
Runtime totalizer
Maintenance messages (events) are generated via the runtime totalizers. These are typically reset when
the maintenance has been carried out. The present operating hours [PrOph] output can be used to connect
the runtime totalization feature for further use in the program (e.g., for changeover of pumps or boilers
based on operating hours).
Resetting the runtime total
The operating hours [Oph] input is used to reset the current runtime total. In online test mode in Xworks
Plus (XWP) via a BACnet client the present value can be reset by overwriting it with a new value (usually
0). This reset does not affect the total operating hours count (pins [OphTot] and [PrOphTot], total
operating hours and present total operating hours respectively).
Overall runtime totalizer
The total operating hours count records the total hours run by an aggregate. It is only reset when the
aggregate is replaced. The [PrOphTot] output is available for further interconnection in the program.
Resetting the operating hours total
The [OphTot] input is used to reset the total operating hours. In online test mode in Xworks Plus (XWP) or
via a BACnet client, the present value can be reset by overwriting it with a new value (usually 0). This reset
procedure simultaneously sets the runtime totalizer (pins [Oph] and [PrOph]) to the same value.
This is necessary, e.g., for an aggregate which is installed as a replacement item, but which has previously
been in operation elsewhere for some time.
Maintenance message