User's Manual
Table Of Contents
- Contents
- List of Tables
- List of Figures
- 1 Introduction and Important Notes
- 2 Overview
- 3 Planning a HiPath Cordless IP System
- 3.1 Planning According to Call Traffic Load
- 3.2 General
- 3.3 Propagation Conditions for Radio Traffic
- 3.4 Determining the Installation Site
- 3.5 Installing Base Stations
- 4 Putting Into Service
- 5 Installation and Administration
- 5.1 Terminology
- 5.2 Network Concept
- 5.3 Synchronisation over air concept
- 5.4 WBM related issues
- 5.5 Phone related issues
- 5.6 Partition concept of BSIP1
- 5.7 Factory reset of BSIP1
- 5.8 Release notes
- 5.9 Quick Start
- 5.10 Quick start overview
- 5.11 Prepare and connect hardware
- 5.12 Configure BSIP1 for IWU mode
- 5.13 Configuration of VoIP (Infrastructure) network
- 5.14 Configuration of DECT network
- 5.15 Configuration of users at the PBX
- 5.16 Configuration of users at the BSIP IWU
- 5.17 Start system services and register handsets
- 5.18 Configure further BSIP Only to the system
- 5.19 "Quick Start" Completion
- 5.20 Further steps
- 5.21 Configuration reference
- 5.22 WBM overview
- 5.23 Administration
- 5.24 "Network/Gateways" Configuration
- 5.25 "Group" Configuration
- 5.26 Users Configuration
- 5.27 Dect Configuration
- 5.27.1 Configuration Page "Dect - Device"
- 5.27.2 Configuration Page "Dect - Sync"
- 5.27.3 Configuration Page "Dect - ARI"
- 5.27.4 Configuration Page "Dect - About"
- 5.27.5 Configuration Page "Dect - Radio" (Advanced mode)
- 5.27.6 Configuration Page "Dect - Call" (Advanced mode)
- 5.27.7 Configuration Page "Dect - Debug" (Advanced mode)
- 5.27.8 General DECT configuration
- 5.28 Debugging Configuration
- 5.29 "Status" Configuration
- 5.30 "System" Configuration
- 5.31 Configuration Hints for PBXs
- 5.32 HiPath OpenOffice EE
- 5.33 HiPath OpenOffice ME
- 5.34 Troubleshooting / FAQ
- 5.35 Configuration hints for Web Browser
- 6 Technical Data
- 7 Diagnosis and Maintenance
- 8 Open Source Software used in the Product
- Index
Installation and Administration
c05_ikon.fm
Administration
A31003-C1010-S100-2-7620, 08/2010
96 HiPath Cordless IP, Service Manual
5.23.2.2 Other options
[Reboot Board]
Using this Button the BSIP1 will start the reboot process after a confirmation
dialog.
[Switch Applic Mode]
To change the mode of the BSIP1 between BSIP1 Only to BSIP1 IWU select
[Switch Applic Mode].
•Hint: The current working mode is printed out at the bottom sstaus line
(APPLICTYPE=BSIPONLY or BSIPIWU) and in the output of [Network
State].
After changing the application mode, the following message box will appear.
Press [OK] to reboot the BSIP1 and start it in the other application mode.
• Important note: After changing the application mode the BSIP1 will start
with the IP configuration which was configured last for the corresponding
application mode. This may be the default configuration for the mode or
the already configured addresses for the mode.
[Factory setting]
Using this functionality, a factory reset of the BSIP1 may be initiated.
This functionality may be used alternatively to the procedure of factory reset
by power sequencing described in chapter 5.7, “Factory reset of BSIP1”.
[Network State]
The output of the Network states functionality displays summarised infor-
mation about the systems network configuration.