User's Manual
Table Of Contents
- Contents
- List of Tables
- List of Figures
- 1 Introduction and Important Notes
- 2 Overview
- 3 Planning a HiPath Cordless IP System
- 3.1 Planning According to Call Traffic Load
- 3.2 General
- 3.3 Propagation Conditions for Radio Traffic
- 3.4 Determining the Installation Site
- 3.5 Installing Base Stations
- 4 Putting Into Service
- 5 Installation and Administration
- 5.1 Terminology
- 5.2 Network Concept
- 5.3 Synchronisation over air concept
- 5.4 WBM related issues
- 5.5 Phone related issues
- 5.6 Partition concept of BSIP1
- 5.7 Factory reset of BSIP1
- 5.8 Release notes
- 5.9 Quick Start
- 5.10 Quick start overview
- 5.11 Prepare and connect hardware
- 5.12 Configure BSIP1 for IWU mode
- 5.13 Configuration of VoIP (Infrastructure) network
- 5.14 Configuration of DECT network
- 5.15 Configuration of users at the PBX
- 5.16 Configuration of users at the BSIP IWU
- 5.17 Start system services and register handsets
- 5.18 Configure further BSIP Only to the system
- 5.19 "Quick Start" Completion
- 5.20 Further steps
- 5.21 Configuration reference
- 5.22 WBM overview
- 5.23 Administration
- 5.24 "Network/Gateways" Configuration
- 5.25 "Group" Configuration
- 5.26 Users Configuration
- 5.27 Dect Configuration
- 5.27.1 Configuration Page "Dect - Device"
- 5.27.2 Configuration Page "Dect - Sync"
- 5.27.3 Configuration Page "Dect - ARI"
- 5.27.4 Configuration Page "Dect - About"
- 5.27.5 Configuration Page "Dect - Radio" (Advanced mode)
- 5.27.6 Configuration Page "Dect - Call" (Advanced mode)
- 5.27.7 Configuration Page "Dect - Debug" (Advanced mode)
- 5.27.8 General DECT configuration
- 5.28 Debugging Configuration
- 5.29 "Status" Configuration
- 5.30 "System" Configuration
- 5.31 Configuration Hints for PBXs
- 5.32 HiPath OpenOffice EE
- 5.33 HiPath OpenOffice ME
- 5.34 Troubleshooting / FAQ
- 5.35 Configuration hints for Web Browser
- 6 Technical Data
- 7 Diagnosis and Maintenance
- 8 Open Source Software used in the Product
- Index
c05_ikon.fm
Installation and Administration
Administration
A31003-C1010-S100-2-7620, 08/2010
HiPath Cordless IP, Service Manual 95
5.23.2.1 [System Update]
Updating the system software
• Important: If you update the system software, the Update is always
applied to the NON-active system. Furthermore, the current configuration
of the active system will be applied to the NON-active system. You have
to ensure to use the SAME software version at all BSIPs. Therefore,
updating the software has to take place at the BSIP IWU AND at all BSIP
Only.
A downgrade is not fully supported. In need of a downgrade, a factory reset
is applied automatically. Please refer to the delivered Release notes of the
new version for details of the update process.
Create a backup of the old configuration (Page Registration - [Backup Config].
Update instructions
1. Please create a backup of the old configuration (Page Registration -
[Backup Config].
2. Ensure that you have a firmware file of the old version available (in case
of a necessary downgrade).
3. Start with the update for the BSIP1 running the HiPath Cordless IP Server
Software (BSIP1 IWU) and reboot the BSIP1 IWU as described in
chapter 5.23.2.2, “Other options”.
Hint: Don’t forget to clear the browser cache after updating a partition.
4. Apply the update to all BSIP1 Only modules and reboot them.
Hint: Don’t forget to clear the browser cache after updating a partition.
5. Restart the services at the BSIP1 IWU.
6. Clear cache of Browser (Very Important). After updating to the new
version the cache of the browser has to be cleared. Otherwise sporadic
problems with the new version will occure since old (cached) configu-
ration pages are used by the browser.
To clear the cache of your browser:
1. Restart your browser.
2. Clear the browser cache of MS Internet Explorer MSIE6:
Tools -> Internet Options -> General -> Temporary Internet Files -> Delete
MSIE7: Tools - Internet Options - General - Browsing history - Delete -
Temporary Internet Files.