User's Manual
Table Of Contents
- Contents
- List of Tables
- List of Figures
- 1 Introduction and Important Notes
- 2 Overview
- 3 Planning a HiPath Cordless IP System
- 3.1 Planning According to Call Traffic Load
- 3.2 General
- 3.3 Propagation Conditions for Radio Traffic
- 3.4 Determining the Installation Site
- 3.5 Installing Base Stations
- 4 Putting Into Service
- 5 Installation and Administration
- 5.1 Terminology
- 5.2 Network Concept
- 5.3 Synchronisation over air concept
- 5.4 WBM related issues
- 5.5 Phone related issues
- 5.6 Partition concept of BSIP1
- 5.7 Factory reset of BSIP1
- 5.8 Release notes
- 5.9 Quick Start
- 5.10 Quick start overview
- 5.11 Prepare and connect hardware
- 5.12 Configure BSIP1 for IWU mode
- 5.13 Configuration of VoIP (Infrastructure) network
- 5.14 Configuration of DECT network
- 5.15 Configuration of users at the PBX
- 5.16 Configuration of users at the BSIP IWU
- 5.17 Start system services and register handsets
- 5.18 Configure further BSIP Only to the system
- 5.19 "Quick Start" Completion
- 5.20 Further steps
- 5.21 Configuration reference
- 5.22 WBM overview
- 5.23 Administration
- 5.24 "Network/Gateways" Configuration
- 5.25 "Group" Configuration
- 5.26 Users Configuration
- 5.27 Dect Configuration
- 5.27.1 Configuration Page "Dect - Device"
- 5.27.2 Configuration Page "Dect - Sync"
- 5.27.3 Configuration Page "Dect - ARI"
- 5.27.4 Configuration Page "Dect - About"
- 5.27.5 Configuration Page "Dect - Radio" (Advanced mode)
- 5.27.6 Configuration Page "Dect - Call" (Advanced mode)
- 5.27.7 Configuration Page "Dect - Debug" (Advanced mode)
- 5.27.8 General DECT configuration
- 5.28 Debugging Configuration
- 5.29 "Status" Configuration
- 5.30 "System" Configuration
- 5.31 Configuration Hints for PBXs
- 5.32 HiPath OpenOffice EE
- 5.33 HiPath OpenOffice ME
- 5.34 Troubleshooting / FAQ
- 5.35 Configuration hints for Web Browser
- 6 Technical Data
- 7 Diagnosis and Maintenance
- 8 Open Source Software used in the Product
- Index
Installation and Administration
c05_ikon.fm
"Quick Start" Completion
A31003-C1010-S100-2-7620, 08/2010
84 HiPath Cordless IP, Service Manual
19. Confirm the message box by clicking on [OK].
The following process will transfer the new settings to the BSIP1 Only.
Therefore, the BSIP1 Only will rebooted automatically by the system.
20. Wait about 1 minute until the BSIP1 is started completely (LED states
should be green/red)
21. At the WBM of the BSIP1 IWU switch to configuration page "System".
22. Start the services by clicking the [System Start] button at the bottom
section.
After the system services are started successfully, telephony functionality is
available.
5.19 "Quick Start" Completion
After you have accomplished some successful test calls you may configure
all additional Users and additional BSIP1 Only in your System.
At this step it's a good idea to backup the configuration. For details refer to
chapter 5.23.1.2, “Button [Backup Config]”
5.20 Further steps
5.20.1 Radio frequency site survey
A radio frequency site survey has to be performed. Within this step, also the
synchronisation concept has to be designed, implemented and tested.
5.20.2 Synchronisation implementation
The syncronisation implementation should be part of the radio frequency site
survey.
For details of synchronisation via air refer to chapter 5.3, “Synchronisation
over air concept”.
5.21 Configuration reference
For the configuration of the HiPath Cordless IP system you have to connect
via a Browser to the BSIP1 IWU.