User's Manual
Table Of Contents
- Contents
- List of Tables
- List of Figures
- 1 Introduction and Important Notes
- 2 Overview
- 3 Planning a HiPath Cordless IP System
- 3.1 Planning According to Call Traffic Load
- 3.2 General
- 3.3 Propagation Conditions for Radio Traffic
- 3.4 Determining the Installation Site
- 3.5 Installing Base Stations
- 4 Putting Into Service
- 5 Installation and Administration
- 5.1 Terminology
- 5.2 Network Concept
- 5.3 Synchronisation over air concept
- 5.4 WBM related issues
- 5.5 Phone related issues
- 5.6 Partition concept of BSIP1
- 5.7 Factory reset of BSIP1
- 5.8 Release notes
- 5.9 Quick Start
- 5.10 Quick start overview
- 5.11 Prepare and connect hardware
- 5.12 Configure BSIP1 for IWU mode
- 5.13 Configuration of VoIP (Infrastructure) network
- 5.14 Configuration of DECT network
- 5.15 Configuration of users at the PBX
- 5.16 Configuration of users at the BSIP IWU
- 5.17 Start system services and register handsets
- 5.18 Configure further BSIP Only to the system
- 5.19 "Quick Start" Completion
- 5.20 Further steps
- 5.21 Configuration reference
- 5.22 WBM overview
- 5.23 Administration
- 5.24 "Network/Gateways" Configuration
- 5.25 "Group" Configuration
- 5.26 Users Configuration
- 5.27 Dect Configuration
- 5.27.1 Configuration Page "Dect - Device"
- 5.27.2 Configuration Page "Dect - Sync"
- 5.27.3 Configuration Page "Dect - ARI"
- 5.27.4 Configuration Page "Dect - About"
- 5.27.5 Configuration Page "Dect - Radio" (Advanced mode)
- 5.27.6 Configuration Page "Dect - Call" (Advanced mode)
- 5.27.7 Configuration Page "Dect - Debug" (Advanced mode)
- 5.27.8 General DECT configuration
- 5.28 Debugging Configuration
- 5.29 "Status" Configuration
- 5.30 "System" Configuration
- 5.31 Configuration Hints for PBXs
- 5.32 HiPath OpenOffice EE
- 5.33 HiPath OpenOffice ME
- 5.34 Troubleshooting / FAQ
- 5.35 Configuration hints for Web Browser
- 6 Technical Data
- 7 Diagnosis and Maintenance
- 8 Open Source Software used in the Product
- Index
Installation and Administration
c05_ikon.fm
Start system services and register handsets
A31003-C1010-S100-2-7620, 08/2010
78 HiPath Cordless IP, Service Manual
5.17 Start system services and register handsets
5.17.1 Start system services
1. Switch to configuration page "System".
To start the functionality of the BSIP1 IWU you first have to start the
system services.
2. Start the services by clicking the [System Start] button at the bottom
section.
3. Check if the system services are running by clicking at the [Refresh]
button several times.
If the system services are started correctly (both states displayed as
"Running", the LED state at the BSIP1 IWU should change from orange/
orange to green/off.
If a time server is configured correctly and can be contacted, the field "Up
since" should display actual local time values, otherwise time will start at
"01.01.1970 00:00".
5.17.2 Register handsets
1. Switch to configuration page "User-Dect".
• Prepare one handset for the registration process.
• Attention: Do not confirm the following procedure at the Handset right
now!
Start the Registration procedure via the menu at the Handset. Choose
any Base Station for the Registration at the handset. Enter the
SystemPIN (preconfigured to "00000000" at configuration page "DECT"
as PIN at the handset (Attention: Do not confirm yet!).
2. Select the corresponding user in the WBM to which the handset has to be
assigned to.