User's Manual
Table Of Contents
- Contents
- List of Tables
- List of Figures
- 1 Introduction and Important Notes
- 2 Overview
- 3 Planning a HiPath Cordless IP System
- 3.1 Planning According to Call Traffic Load
- 3.2 General
- 3.3 Propagation Conditions for Radio Traffic
- 3.4 Determining the Installation Site
- 3.5 Installing Base Stations
- 4 Putting Into Service
- 5 Installation and Administration
- 5.1 Terminology
- 5.2 Network Concept
- 5.3 Synchronisation over air concept
- 5.4 WBM related issues
- 5.5 Phone related issues
- 5.6 Partition concept of BSIP1
- 5.7 Factory reset of BSIP1
- 5.8 Release notes
- 5.9 Quick Start
- 5.10 Quick start overview
- 5.11 Prepare and connect hardware
- 5.12 Configure BSIP1 for IWU mode
- 5.13 Configuration of VoIP (Infrastructure) network
- 5.14 Configuration of DECT network
- 5.15 Configuration of users at the PBX
- 5.16 Configuration of users at the BSIP IWU
- 5.17 Start system services and register handsets
- 5.18 Configure further BSIP Only to the system
- 5.19 "Quick Start" Completion
- 5.20 Further steps
- 5.21 Configuration reference
- 5.22 WBM overview
- 5.23 Administration
- 5.24 "Network/Gateways" Configuration
- 5.25 "Group" Configuration
- 5.26 Users Configuration
- 5.27 Dect Configuration
- 5.27.1 Configuration Page "Dect - Device"
- 5.27.2 Configuration Page "Dect - Sync"
- 5.27.3 Configuration Page "Dect - ARI"
- 5.27.4 Configuration Page "Dect - About"
- 5.27.5 Configuration Page "Dect - Radio" (Advanced mode)
- 5.27.6 Configuration Page "Dect - Call" (Advanced mode)
- 5.27.7 Configuration Page "Dect - Debug" (Advanced mode)
- 5.27.8 General DECT configuration
- 5.28 Debugging Configuration
- 5.29 "Status" Configuration
- 5.30 "System" Configuration
- 5.31 Configuration Hints for PBXs
- 5.32 HiPath OpenOffice EE
- 5.33 HiPath OpenOffice ME
- 5.34 Troubleshooting / FAQ
- 5.35 Configuration hints for Web Browser
- 6 Technical Data
- 7 Diagnosis and Maintenance
- 8 Open Source Software used in the Product
- Index
Installation and Administration
c05_ikon.fm
Configuration of users at the BSIP IWU
A31003-C1010-S100-2-7620, 08/2010
76 HiPath Cordless IP, Service Manual
The default configuration already contains an entry for a Group, which is
used for assigning the Users to the Gateways, so you do not need to
make changes here.
7. Add a new group by clicking on the button [Add Group].
8. Change the contents of the following fields.
Name
Change the preconfigured name of the Group (e.g. to the name of the
corresponding PBX) . This name is only used for the internal configuration
of the BSIP Software.
Gateways
Select the gateway from the dropdown field which you have configured in
the last step.
5.16.2 User
1. Switch to configuration page "User", sub page User ("User -User").
Set up one or several Users according the user configuration at the PBX
for the connection with the BSIP1. Please take care of the consistency of
the entries between the PBX and the BSIP1.
2. Add a new user by clicking on the button [Add User].
•Hint: For the correlation of the fields between the BSIP and the PBX refer
to chapter 5.33.4, “Station Configuration - IP-DECT IWU”.
3. Change the contents of the following fields:
Msn (necessary)
The MSN has to correlate with the Callnumber of the User at the PBX.
DisplayName (necessary)
This information is shown at the idle display of the corresponding
handset.