User's Manual
Table Of Contents
- Contents
- List of Tables
- List of Figures
- 1 Introduction and Important Notes
- 2 Overview
- 3 Planning a HiPath Cordless IP System
- 3.1 Planning According to Call Traffic Load
- 3.2 General
- 3.3 Propagation Conditions for Radio Traffic
- 3.4 Determining the Installation Site
- 3.5 Installing Base Stations
- 4 Putting Into Service
- 5 Installation and Administration
- 5.1 Terminology
- 5.2 Network Concept
- 5.3 Synchronisation over air concept
- 5.4 WBM related issues
- 5.5 Phone related issues
- 5.6 Partition concept of BSIP1
- 5.7 Factory reset of BSIP1
- 5.8 Release notes
- 5.9 Quick Start
- 5.10 Quick start overview
- 5.11 Prepare and connect hardware
- 5.12 Configure BSIP1 for IWU mode
- 5.13 Configuration of VoIP (Infrastructure) network
- 5.14 Configuration of DECT network
- 5.15 Configuration of users at the PBX
- 5.16 Configuration of users at the BSIP IWU
- 5.17 Start system services and register handsets
- 5.18 Configure further BSIP Only to the system
- 5.19 "Quick Start" Completion
- 5.20 Further steps
- 5.21 Configuration reference
- 5.22 WBM overview
- 5.23 Administration
- 5.24 "Network/Gateways" Configuration
- 5.25 "Group" Configuration
- 5.26 Users Configuration
- 5.27 Dect Configuration
- 5.27.1 Configuration Page "Dect - Device"
- 5.27.2 Configuration Page "Dect - Sync"
- 5.27.3 Configuration Page "Dect - ARI"
- 5.27.4 Configuration Page "Dect - About"
- 5.27.5 Configuration Page "Dect - Radio" (Advanced mode)
- 5.27.6 Configuration Page "Dect - Call" (Advanced mode)
- 5.27.7 Configuration Page "Dect - Debug" (Advanced mode)
- 5.27.8 General DECT configuration
- 5.28 Debugging Configuration
- 5.29 "Status" Configuration
- 5.30 "System" Configuration
- 5.31 Configuration Hints for PBXs
- 5.32 HiPath OpenOffice EE
- 5.33 HiPath OpenOffice ME
- 5.34 Troubleshooting / FAQ
- 5.35 Configuration hints for Web Browser
- 6 Technical Data
- 7 Diagnosis and Maintenance
- 8 Open Source Software used in the Product
- Index
c05_ikon.fm
Installation and Administration
Configuration of users at the PBX
A31003-C1010-S100-2-7620, 08/2010
HiPath Cordless IP, Service Manual 75
HTTPS Enabled = [X]use https://{Server Ip of IP VoIP (Infrastructure)
Network}
Example: https://192.168.201.114
5.15 Configuration of users at the PBX
It is assumed that the VoIP users at the PBX are already configured. For detail
refer to Section 5.31.
5.16 Configuration of users at the BSIP IWU
5.16.1 Gateway and Group
1. Access the WBM of the BSIP1 IWU WBM via the web browser at the
maintenance PC.
Example: https://192.168.201.114
2. Log in to the WBM with Username "Siemens".
3. Switch to configuration page "Network/Gateways".
4. Add a new gateway entry by clicking on the button [Add Gateway].
5. Change the following values:
Name
Change the preconfigured name of the PBX to a descriptive name for the
VoIP Gateway. This name is only used for the internal configuration of the
BSIP Software.
Remote IP address and Netmask
Change the preconfigured "Remote IP address" as well as the corres-
ponding "Netmask" to the ip address of your PBX.
6. Switch to configuration page "Group"
Groups are the connecting link between the "Gateways" and the VoIP
Users. A User is assigned to a Group and a Group is assigned to a
"Gateway".