User's Manual
Table Of Contents
- Contents
- List of Tables
- List of Figures
- 1 Introduction and Important Notes
- 2 Overview
- 3 Planning a HiPath Cordless IP System
- 3.1 Planning According to Call Traffic Load
- 3.2 General
- 3.3 Propagation Conditions for Radio Traffic
- 3.4 Determining the Installation Site
- 3.5 Installing Base Stations
- 4 Putting Into Service
- 5 Installation and Administration
- 5.1 Terminology
- 5.2 Network Concept
- 5.3 Synchronisation over air concept
- 5.4 WBM related issues
- 5.5 Phone related issues
- 5.6 Partition concept of BSIP1
- 5.7 Factory reset of BSIP1
- 5.8 Release notes
- 5.9 Quick Start
- 5.10 Quick start overview
- 5.11 Prepare and connect hardware
- 5.12 Configure BSIP1 for IWU mode
- 5.13 Configuration of VoIP (Infrastructure) network
- 5.14 Configuration of DECT network
- 5.15 Configuration of users at the PBX
- 5.16 Configuration of users at the BSIP IWU
- 5.17 Start system services and register handsets
- 5.18 Configure further BSIP Only to the system
- 5.19 "Quick Start" Completion
- 5.20 Further steps
- 5.21 Configuration reference
- 5.22 WBM overview
- 5.23 Administration
- 5.24 "Network/Gateways" Configuration
- 5.25 "Group" Configuration
- 5.26 Users Configuration
- 5.27 Dect Configuration
- 5.27.1 Configuration Page "Dect - Device"
- 5.27.2 Configuration Page "Dect - Sync"
- 5.27.3 Configuration Page "Dect - ARI"
- 5.27.4 Configuration Page "Dect - About"
- 5.27.5 Configuration Page "Dect - Radio" (Advanced mode)
- 5.27.6 Configuration Page "Dect - Call" (Advanced mode)
- 5.27.7 Configuration Page "Dect - Debug" (Advanced mode)
- 5.27.8 General DECT configuration
- 5.28 Debugging Configuration
- 5.29 "Status" Configuration
- 5.30 "System" Configuration
- 5.31 Configuration Hints for PBXs
- 5.32 HiPath OpenOffice EE
- 5.33 HiPath OpenOffice ME
- 5.34 Troubleshooting / FAQ
- 5.35 Configuration hints for Web Browser
- 6 Technical Data
- 7 Diagnosis and Maintenance
- 8 Open Source Software used in the Product
- Index
Installation and Administration
c05_ikon.fm
Configuration of DECT network
A31003-C1010-S100-2-7620, 08/2010
74 HiPath Cordless IP, Service Manual
System Pin
The "PIN" is a 8-digit number and it is needed for the registration of
handsets. It is preconfigured with "00000000" and may be configured
systemwide here. You can change the system pin to another decimal
value.
IWU as GW
Activate this option to use the BSIP1 IWU as a router to the BSIP1 Only.
• Background: Using the option "IWU as GW" enables the routing (ip
forwarding) via the IP VoIP (Infrastructure) Network to the DECT Network.
This ensures access to the network in which the BSIP Only are located,
without having an ip address (in the DECT network) configured at the
maintenance PC. Additionaly you have to add a route at the maintenance
PC
3. Apply the changes by clicking the [Apply] button at the bottom section.
4. Confirm the message box by clicking on [OK].
As stated above, for the changes to become active, the BSIP1 has to be
rebooted.
• Important: After rebooting, the BSIP1 will not be accessible by its the ip
address 192.168.2.1 anymore. Instead it is accessible by the ip address
of the IP VoIP (Infrastructure) Network (configured at the step above). If
you have attached the BSIP1 directly via a ethernet cable you have to
attach the BSIP1 physically to the designated network segment after
rebooting it.
5. Select the configuration page "Administration".
6. Initiate the reboot by clicking the [Reboot Board] button.
Wait about 1 minute for the board to come up again. The board LEDs
should change to permanently orange / orange.
7. Access the WBM (Web based management) by the in address you have
configured before for the IP VoIP (Infrastructure) Network.
Depending on the http access mode you have to use http:// or https://
mode
HTTPS Enabled = [ ]use http://{Server Ip of IP VoIP (Infrastructure)
Network}