User's Manual
Table Of Contents
- Contents
- List of Tables
- List of Figures
- 1 Introduction and Important Notes
- 2 Overview
- 3 Planning a HiPath Cordless IP System
- 3.1 Planning According to Call Traffic Load
- 3.2 General
- 3.3 Propagation Conditions for Radio Traffic
- 3.4 Determining the Installation Site
- 3.5 Installing Base Stations
- 4 Putting Into Service
- 5 Installation and Administration
- 5.1 Terminology
- 5.2 Network Concept
- 5.3 Synchronisation over air concept
- 5.4 WBM related issues
- 5.5 Phone related issues
- 5.6 Partition concept of BSIP1
- 5.7 Factory reset of BSIP1
- 5.8 Release notes
- 5.9 Quick Start
- 5.10 Quick start overview
- 5.11 Prepare and connect hardware
- 5.12 Configure BSIP1 for IWU mode
- 5.13 Configuration of VoIP (Infrastructure) network
- 5.14 Configuration of DECT network
- 5.15 Configuration of users at the PBX
- 5.16 Configuration of users at the BSIP IWU
- 5.17 Start system services and register handsets
- 5.18 Configure further BSIP Only to the system
- 5.19 "Quick Start" Completion
- 5.20 Further steps
- 5.21 Configuration reference
- 5.22 WBM overview
- 5.23 Administration
- 5.24 "Network/Gateways" Configuration
- 5.25 "Group" Configuration
- 5.26 Users Configuration
- 5.27 Dect Configuration
- 5.27.1 Configuration Page "Dect - Device"
- 5.27.2 Configuration Page "Dect - Sync"
- 5.27.3 Configuration Page "Dect - ARI"
- 5.27.4 Configuration Page "Dect - About"
- 5.27.5 Configuration Page "Dect - Radio" (Advanced mode)
- 5.27.6 Configuration Page "Dect - Call" (Advanced mode)
- 5.27.7 Configuration Page "Dect - Debug" (Advanced mode)
- 5.27.8 General DECT configuration
- 5.28 Debugging Configuration
- 5.29 "Status" Configuration
- 5.30 "System" Configuration
- 5.31 Configuration Hints for PBXs
- 5.32 HiPath OpenOffice EE
- 5.33 HiPath OpenOffice ME
- 5.34 Troubleshooting / FAQ
- 5.35 Configuration hints for Web Browser
- 6 Technical Data
- 7 Diagnosis and Maintenance
- 8 Open Source Software used in the Product
- Index
c05_ikon.fm
Installation and Administration
Configuration of DECT network
A31003-C1010-S100-2-7620, 08/2010
HiPath Cordless IP, Service Manual 73
Routing entries
If you need routing to another network (e.g. access from maintenance PC
to the IP VoIP (Infrastructure) Network, you can configure the corres-
ponding values either by setting the "Default Gateway" or by a special
"Network destination".
If using the "Network destination" method, you have to configure the fields
"Network destination", "Network mask" and "Gateway" and additionaly
you have to add a route at the maintenance PC.
• Important: Ensure that the ip configuration is configured correctly.
Otherwise - after rebooting the board - it may not be accessible without
resetting it to its factory defaults (which have a fixed IP setting of
192.168.1.1).
5.14 Configuration of DECT network
Since configuration of the DECT Network settings requires a reboot of the
BSIP1, the settings are configured before the BSIP1 hardware is attached to
the designated network segment.
1. Select the the configuration page "Dect".
2. Change the configuration in the bottom frame to the designated values of
the BSIP1 IWU.
Server Ip
This field contains the IP address of the server (the IWU) in the DECT
network.
It is used for communication between all BSIP Only and the BSIP IWU.
SystemAri
In this field the System ARI (DECT ID) which has to be unique at each
DECT system and has been assigned to the system has to be configured.