User's Manual
Table Of Contents
- Contents
- List of Tables
- List of Figures
- 1 Introduction and Important Notes
- 2 Overview
- 3 Planning a HiPath Cordless IP System
- 3.1 Planning According to Call Traffic Load
- 3.2 General
- 3.3 Propagation Conditions for Radio Traffic
- 3.4 Determining the Installation Site
- 3.5 Installing Base Stations
- 4 Putting Into Service
- 5 Installation and Administration
- 5.1 Terminology
- 5.2 Network Concept
- 5.3 Synchronisation over air concept
- 5.4 WBM related issues
- 5.5 Phone related issues
- 5.6 Partition concept of BSIP1
- 5.7 Factory reset of BSIP1
- 5.8 Release notes
- 5.9 Quick Start
- 5.10 Quick start overview
- 5.11 Prepare and connect hardware
- 5.12 Configure BSIP1 for IWU mode
- 5.13 Configuration of VoIP (Infrastructure) network
- 5.14 Configuration of DECT network
- 5.15 Configuration of users at the PBX
- 5.16 Configuration of users at the BSIP IWU
- 5.17 Start system services and register handsets
- 5.18 Configure further BSIP Only to the system
- 5.19 "Quick Start" Completion
- 5.20 Further steps
- 5.21 Configuration reference
- 5.22 WBM overview
- 5.23 Administration
- 5.24 "Network/Gateways" Configuration
- 5.25 "Group" Configuration
- 5.26 Users Configuration
- 5.27 Dect Configuration
- 5.27.1 Configuration Page "Dect - Device"
- 5.27.2 Configuration Page "Dect - Sync"
- 5.27.3 Configuration Page "Dect - ARI"
- 5.27.4 Configuration Page "Dect - About"
- 5.27.5 Configuration Page "Dect - Radio" (Advanced mode)
- 5.27.6 Configuration Page "Dect - Call" (Advanced mode)
- 5.27.7 Configuration Page "Dect - Debug" (Advanced mode)
- 5.27.8 General DECT configuration
- 5.28 Debugging Configuration
- 5.29 "Status" Configuration
- 5.30 "System" Configuration
- 5.31 Configuration Hints for PBXs
- 5.32 HiPath OpenOffice EE
- 5.33 HiPath OpenOffice ME
- 5.34 Troubleshooting / FAQ
- 5.35 Configuration hints for Web Browser
- 6 Technical Data
- 7 Diagnosis and Maintenance
- 8 Open Source Software used in the Product
- Index
Installation and Administration
c05_ikon.fm
Configuration of VoIP (Infrastructure) network
A31003-C1010-S100-2-7620, 08/2010
72 HiPath Cordless IP, Service Manual
5.13 Configuration of VoIP (Infrastructure) network
Since configuration of the IP VoIP (Infrastructure) Network settings requires
a reboot of the BSIP1, the settings are configured before the BSIP hardware
is attached to the designated network segment.
To allow direct IP communication between the BSIP1 and the PBX both
devices have to be located in the same IP network. Therefore it is necessary
to adapt the IP address of the BSIP1 to the network of the VoIP (Infra-
structure) . You need at least one unused IP address of the Infrastructure
network, which has to be configured at the BSIP1.
1. Select the configuration page "Network/Gateways".
2. Change the configuration in the bottom frame to the designated values of
the BSIP1 IWU.
Change the following values according your needs:
Ip address:
Here you have to configure the ip address at which the BSIP IWU should
be available inside the VoIP (Infrastructure) Network. This also is the
address at which the BSIP1 IWU is accessible via WBM.
Network mask
Enter the corresponding netmask for the IP address as configured above.
(Default for Class C networks: 255.255.255.0).
Time Server Ip
Since the BSIP1 has no hardware clock, time has to be set according a
NTP (or SNTP) time server. After activating the NTP Server at the PBX,
it may take some minutes upon activation of the NTP service. This is due
to the nature of time synchronisation between NTP server and NTP client.
For details configuring time server at the PBX refer to "chapter 5.31,
“Configuration Hints for PBXs”.
https
Activate the https access mode.