User's Manual
Table Of Contents
- Contents
- List of Tables
- List of Figures
- 1 Introduction and Important Notes
- 2 Overview
- 3 Planning a HiPath Cordless IP System
- 3.1 Planning According to Call Traffic Load
- 3.2 General
- 3.3 Propagation Conditions for Radio Traffic
- 3.4 Determining the Installation Site
- 3.5 Installing Base Stations
- 4 Putting Into Service
- 5 Installation and Administration
- 5.1 Terminology
- 5.2 Network Concept
- 5.3 Synchronisation over air concept
- 5.4 WBM related issues
- 5.5 Phone related issues
- 5.6 Partition concept of BSIP1
- 5.7 Factory reset of BSIP1
- 5.8 Release notes
- 5.9 Quick Start
- 5.10 Quick start overview
- 5.11 Prepare and connect hardware
- 5.12 Configure BSIP1 for IWU mode
- 5.13 Configuration of VoIP (Infrastructure) network
- 5.14 Configuration of DECT network
- 5.15 Configuration of users at the PBX
- 5.16 Configuration of users at the BSIP IWU
- 5.17 Start system services and register handsets
- 5.18 Configure further BSIP Only to the system
- 5.19 "Quick Start" Completion
- 5.20 Further steps
- 5.21 Configuration reference
- 5.22 WBM overview
- 5.23 Administration
- 5.24 "Network/Gateways" Configuration
- 5.25 "Group" Configuration
- 5.26 Users Configuration
- 5.27 Dect Configuration
- 5.27.1 Configuration Page "Dect - Device"
- 5.27.2 Configuration Page "Dect - Sync"
- 5.27.3 Configuration Page "Dect - ARI"
- 5.27.4 Configuration Page "Dect - About"
- 5.27.5 Configuration Page "Dect - Radio" (Advanced mode)
- 5.27.6 Configuration Page "Dect - Call" (Advanced mode)
- 5.27.7 Configuration Page "Dect - Debug" (Advanced mode)
- 5.27.8 General DECT configuration
- 5.28 Debugging Configuration
- 5.29 "Status" Configuration
- 5.30 "System" Configuration
- 5.31 Configuration Hints for PBXs
- 5.32 HiPath OpenOffice EE
- 5.33 HiPath OpenOffice ME
- 5.34 Troubleshooting / FAQ
- 5.35 Configuration hints for Web Browser
- 6 Technical Data
- 7 Diagnosis and Maintenance
- 8 Open Source Software used in the Product
- Index
c05_ikon.fm
Installation and Administration
Configure BSIP1 for IWU mode
A31003-C1010-S100-2-7620, 08/2010
HiPath Cordless IP, Service Manual 71
The BSIP1 is accessible via the factory default IP address 192.168.2.1 in
BSIP1 IWU mode. To access the BSIP1 IWU WBM you have to configure an
IP address in the network 192.168.2.0/255.255.255.0, e.g. 192.168.2.101 on
your Maintenance PC.
1. If the IP address 192.168.2.1 is used in your network, you first have to
directly connect the Maintenance PC and the BSIP1 via ethernet. This
may be done with a direct ethernet connection via the power injector or
via a separate ethernet switch where only the Maintenance PC and the
BSIP1 are connected.
2. Test via ping, if the BSIP1 is replying to the ping requests at ip address
(ping 192.168.2.1).
3. If not, check all cabling, switch settings, (e.g VLAN configuration).
4. Ensure that the configured local IP of the maintenance PC adress is up
(e.g ping 192.168.2.101).
5. Access the WBM (Web based management) at the following URL: http://
192.168.2.1
6. Log in to the WBM with the following (case-sensitive) credentials:
7. Username: Siemens, Password: 1q21q2
8. Press the [Login] button. The configuration page for the BSIP1 in BSIP1
Only mode appears.