User's Manual
Table Of Contents
- Contents
- List of Tables
- List of Figures
- 1 Introduction and Important Notes
- 2 Overview
- 3 Planning a HiPath Cordless IP System
- 3.1 Planning According to Call Traffic Load
- 3.2 General
- 3.3 Propagation Conditions for Radio Traffic
- 3.4 Determining the Installation Site
- 3.5 Installing Base Stations
- 4 Putting Into Service
- 5 Installation and Administration
- 5.1 Terminology
- 5.2 Network Concept
- 5.3 Synchronisation over air concept
- 5.4 WBM related issues
- 5.5 Phone related issues
- 5.6 Partition concept of BSIP1
- 5.7 Factory reset of BSIP1
- 5.8 Release notes
- 5.9 Quick Start
- 5.10 Quick start overview
- 5.11 Prepare and connect hardware
- 5.12 Configure BSIP1 for IWU mode
- 5.13 Configuration of VoIP (Infrastructure) network
- 5.14 Configuration of DECT network
- 5.15 Configuration of users at the PBX
- 5.16 Configuration of users at the BSIP IWU
- 5.17 Start system services and register handsets
- 5.18 Configure further BSIP Only to the system
- 5.19 "Quick Start" Completion
- 5.20 Further steps
- 5.21 Configuration reference
- 5.22 WBM overview
- 5.23 Administration
- 5.24 "Network/Gateways" Configuration
- 5.25 "Group" Configuration
- 5.26 Users Configuration
- 5.27 Dect Configuration
- 5.27.1 Configuration Page "Dect - Device"
- 5.27.2 Configuration Page "Dect - Sync"
- 5.27.3 Configuration Page "Dect - ARI"
- 5.27.4 Configuration Page "Dect - About"
- 5.27.5 Configuration Page "Dect - Radio" (Advanced mode)
- 5.27.6 Configuration Page "Dect - Call" (Advanced mode)
- 5.27.7 Configuration Page "Dect - Debug" (Advanced mode)
- 5.27.8 General DECT configuration
- 5.28 Debugging Configuration
- 5.29 "Status" Configuration
- 5.30 "System" Configuration
- 5.31 Configuration Hints for PBXs
- 5.32 HiPath OpenOffice EE
- 5.33 HiPath OpenOffice ME
- 5.34 Troubleshooting / FAQ
- 5.35 Configuration hints for Web Browser
- 6 Technical Data
- 7 Diagnosis and Maintenance
- 8 Open Source Software used in the Product
- Index
Installation and Administration
c05_ikon.fm
Prepare and connect hardware
A31003-C1010-S100-2-7620, 08/2010
68 HiPath Cordless IP, Service Manual
5.11 Prepare and connect hardware
1. Attach the first BSIP1 to a PoE port of the network switch or via a Power
injector to a standard port of the network switch. Wait about 1 minute until
the LED states of the BSIP1 change to permanently green and red.
2. Meanwhile you may connect the maintenance PC to a switch port via a
ethernet cable.
•Hint: The BSIP1 devices MUST NOT be separated by layer 3 Routing
devices. Only separation via Layer 2 switches is supported.
5.12 Configure BSIP1 for IWU mode
1. The BSIP1 is accessible via its factory default IP address 192.168.1.1 in
BSIP1 Only mode.
To access the BSIP1 Only WBM you have to configure an IP address in
the network 192.168.1.0/255.255.255.0, e.g. 192.168.1.101 on your
maintenance PC.
2. If the IP address 192.168.1.1 is used in your network, you first have to
directly connect the maintenance PC and the BSIP1 via ethernet. This
may be done with a direct ethernet connection via the power injector or
via a separate ethernet switch where only the Maintenance PC and the
BSIP1 are connected.
3. Test via ping, if the BSIP1 is replying to the ping requests at ip address
(ping 192.168.1.1).
4. If not, check all cabling, switch settings, (e.g VLAN configuration).
5. Ensure that the configured local IP of the maintenance PC adress is up
(e.g ping 192.168.1.101).
6. If you don't get replies consider to reset the BSIP to its factory defaults
(see chapter 5.7, “Factory reset of BSIP1”).
7. Start the Web browser at the Maintenance PC
8. Access the WBM (Web based management) at the following URL: http://
192.168.1.1