User's Manual
Table Of Contents
- Contents
- List of Tables
- List of Figures
- 1 Introduction and Important Notes
- 2 Overview
- 3 Planning a HiPath Cordless IP System
- 3.1 Planning According to Call Traffic Load
- 3.2 General
- 3.3 Propagation Conditions for Radio Traffic
- 3.4 Determining the Installation Site
- 3.5 Installing Base Stations
- 4 Putting Into Service
- 5 Installation and Administration
- 5.1 Terminology
- 5.2 Network Concept
- 5.3 Synchronisation over air concept
- 5.4 WBM related issues
- 5.5 Phone related issues
- 5.6 Partition concept of BSIP1
- 5.7 Factory reset of BSIP1
- 5.8 Release notes
- 5.9 Quick Start
- 5.10 Quick start overview
- 5.11 Prepare and connect hardware
- 5.12 Configure BSIP1 for IWU mode
- 5.13 Configuration of VoIP (Infrastructure) network
- 5.14 Configuration of DECT network
- 5.15 Configuration of users at the PBX
- 5.16 Configuration of users at the BSIP IWU
- 5.17 Start system services and register handsets
- 5.18 Configure further BSIP Only to the system
- 5.19 "Quick Start" Completion
- 5.20 Further steps
- 5.21 Configuration reference
- 5.22 WBM overview
- 5.23 Administration
- 5.24 "Network/Gateways" Configuration
- 5.25 "Group" Configuration
- 5.26 Users Configuration
- 5.27 Dect Configuration
- 5.27.1 Configuration Page "Dect - Device"
- 5.27.2 Configuration Page "Dect - Sync"
- 5.27.3 Configuration Page "Dect - ARI"
- 5.27.4 Configuration Page "Dect - About"
- 5.27.5 Configuration Page "Dect - Radio" (Advanced mode)
- 5.27.6 Configuration Page "Dect - Call" (Advanced mode)
- 5.27.7 Configuration Page "Dect - Debug" (Advanced mode)
- 5.27.8 General DECT configuration
- 5.28 Debugging Configuration
- 5.29 "Status" Configuration
- 5.30 "System" Configuration
- 5.31 Configuration Hints for PBXs
- 5.32 HiPath OpenOffice EE
- 5.33 HiPath OpenOffice ME
- 5.34 Troubleshooting / FAQ
- 5.35 Configuration hints for Web Browser
- 6 Technical Data
- 7 Diagnosis and Maintenance
- 8 Open Source Software used in the Product
- Index
c05_ikon.fm
Installation and Administration
Phone related issues
A31003-C1010-S100-2-7620, 08/2010
HiPath Cordless IP, Service Manual 65
5.5 Phone related issues
5.5.1 Date / time for phone idle display
The handset displays the local system time in its idle display.
The activation of date / time at the phone idle display is initiated by an
outgoing or incoming call (but no active connection is needed therefore).
If the user changed the LocalTime at the handset, the time will be overwritten
with SystemTime after the next incoming or outgoing call.
•Hint: There is neither an activation of the current date / time due to a
Power cycle of the handset nor to a roaming process.
5.6 Partition concept of BSIP1
To guarantee a functional BSIP1 at any time, two bootable systems are imple-
mented at the BSIP1.
A current system and the fallback system. Therefore the BSIP1 has two
different systems partitions: System 1 and System 2.
Both system partitions can hold their own configuration (although it is
copied from one partition to the other during a firmware update).
Both partitions store their application mode (BSIP Only or BSIP IWU)
A factory reset is always applied to the current system partition. It does not
affect the settings of the other partition.