User's Manual
Table Of Contents
- Contents
- List of Tables
- List of Figures
- 1 Introduction and Important Notes
- 2 Overview
- 3 Planning a HiPath Cordless IP System
- 3.1 Planning According to Call Traffic Load
- 3.2 General
- 3.3 Propagation Conditions for Radio Traffic
- 3.4 Determining the Installation Site
- 3.5 Installing Base Stations
- 4 Putting Into Service
- 5 Installation and Administration
- 5.1 Terminology
- 5.2 Network Concept
- 5.3 Synchronisation over air concept
- 5.4 WBM related issues
- 5.5 Phone related issues
- 5.6 Partition concept of BSIP1
- 5.7 Factory reset of BSIP1
- 5.8 Release notes
- 5.9 Quick Start
- 5.10 Quick start overview
- 5.11 Prepare and connect hardware
- 5.12 Configure BSIP1 for IWU mode
- 5.13 Configuration of VoIP (Infrastructure) network
- 5.14 Configuration of DECT network
- 5.15 Configuration of users at the PBX
- 5.16 Configuration of users at the BSIP IWU
- 5.17 Start system services and register handsets
- 5.18 Configure further BSIP Only to the system
- 5.19 "Quick Start" Completion
- 5.20 Further steps
- 5.21 Configuration reference
- 5.22 WBM overview
- 5.23 Administration
- 5.24 "Network/Gateways" Configuration
- 5.25 "Group" Configuration
- 5.26 Users Configuration
- 5.27 Dect Configuration
- 5.27.1 Configuration Page "Dect - Device"
- 5.27.2 Configuration Page "Dect - Sync"
- 5.27.3 Configuration Page "Dect - ARI"
- 5.27.4 Configuration Page "Dect - About"
- 5.27.5 Configuration Page "Dect - Radio" (Advanced mode)
- 5.27.6 Configuration Page "Dect - Call" (Advanced mode)
- 5.27.7 Configuration Page "Dect - Debug" (Advanced mode)
- 5.27.8 General DECT configuration
- 5.28 Debugging Configuration
- 5.29 "Status" Configuration
- 5.30 "System" Configuration
- 5.31 Configuration Hints for PBXs
- 5.32 HiPath OpenOffice EE
- 5.33 HiPath OpenOffice ME
- 5.34 Troubleshooting / FAQ
- 5.35 Configuration hints for Web Browser
- 6 Technical Data
- 7 Diagnosis and Maintenance
- 8 Open Source Software used in the Product
- Index
c05_ikon.fm
Installation and Administration
WBM related issues
A31003-C1010-S100-2-7620, 08/2010
HiPath Cordless IP, Service Manual 63
Resynchronisation
Important: If a BSIP loses synchronisation it tries to resync to the configured
synchronisation base station. This process can not start until the last call at
this base station is released and no other calls (at the belonging base station)
are active.
5.4 WBM related issues
5.4.1 Supported Web Browser
Supported Web Browsers are:
• Mozilla Firefox Versions 2 (2.0.0.16 ... 2.0.0.18) and Version 3.0.x (3.01 ..
3.0.6) and
• Microsoft Internet Explorer Version 6.x and Version 7.x
For details refer to chapter 5.35, “Configuration hints for Web Browser”.
5.4.2 General WBM issues
• Don't use special characters inside the objects for WBM. Supported
characters are
0-9, a-z, A-Z, "-" "_". Other characters may prevent the system services
from running correctly.
• Don't configure names for objects with more than 20 Characters.
• Changing of IP addresses of BSIP Only - after changes have been
applied, a manual [Scan/Sync] has to be applied to show the new values
• Configuration and firmware files MUST NOT include spaces in their
filenames
• Do not use multiple WBM session to different BSIPs at a single browser
session. This may influence the behaviour of the WBM sessions.
5.4.3 Multiple WBM sessions
If you login onto the same WBM session on which another user is logged on,
you are informed about that by a message box.