User's Manual
Table Of Contents
- Contents
- List of Tables
- List of Figures
- 1 Introduction and Important Notes
- 2 Overview
- 3 Planning a HiPath Cordless IP System
- 3.1 Planning According to Call Traffic Load
- 3.2 General
- 3.3 Propagation Conditions for Radio Traffic
- 3.4 Determining the Installation Site
- 3.5 Installing Base Stations
- 4 Putting Into Service
- 5 Installation and Administration
- 5.1 Terminology
- 5.2 Network Concept
- 5.3 Synchronisation over air concept
- 5.4 WBM related issues
- 5.5 Phone related issues
- 5.6 Partition concept of BSIP1
- 5.7 Factory reset of BSIP1
- 5.8 Release notes
- 5.9 Quick Start
- 5.10 Quick start overview
- 5.11 Prepare and connect hardware
- 5.12 Configure BSIP1 for IWU mode
- 5.13 Configuration of VoIP (Infrastructure) network
- 5.14 Configuration of DECT network
- 5.15 Configuration of users at the PBX
- 5.16 Configuration of users at the BSIP IWU
- 5.17 Start system services and register handsets
- 5.18 Configure further BSIP Only to the system
- 5.19 "Quick Start" Completion
- 5.20 Further steps
- 5.21 Configuration reference
- 5.22 WBM overview
- 5.23 Administration
- 5.24 "Network/Gateways" Configuration
- 5.25 "Group" Configuration
- 5.26 Users Configuration
- 5.27 Dect Configuration
- 5.27.1 Configuration Page "Dect - Device"
- 5.27.2 Configuration Page "Dect - Sync"
- 5.27.3 Configuration Page "Dect - ARI"
- 5.27.4 Configuration Page "Dect - About"
- 5.27.5 Configuration Page "Dect - Radio" (Advanced mode)
- 5.27.6 Configuration Page "Dect - Call" (Advanced mode)
- 5.27.7 Configuration Page "Dect - Debug" (Advanced mode)
- 5.27.8 General DECT configuration
- 5.28 Debugging Configuration
- 5.29 "Status" Configuration
- 5.30 "System" Configuration
- 5.31 Configuration Hints for PBXs
- 5.32 HiPath OpenOffice EE
- 5.33 HiPath OpenOffice ME
- 5.34 Troubleshooting / FAQ
- 5.35 Configuration hints for Web Browser
- 6 Technical Data
- 7 Diagnosis and Maintenance
- 8 Open Source Software used in the Product
- Index
c05_ikon.fm
Installation and Administration
Network Concept
A31003-C1010-S100-2-7620, 08/2010
HiPath Cordless IP, Service Manual 61
5.2 Network Concept
The IP network concept of the HiPath Cordless IP solution System is designed
for the separation into three logical networks:
1. VoIP (Infrastructure) network
Here are the existing infrastructure components (default Gateways,
DHCP servers, Time server, ...), the PBX (the VoIP Gateway) and the
BSIP1 running the HiPath Cordless IP Server Software (the Interworking
Unit [IWU] between VoIP and DECT) part of the BSIP1. This network is
used for the connection of the BSIP1 IWU to the IP and VoIP infra-
structure of the company LAN.
The factory-default network address is 192.168.2.0 with a netmask of
255.255.255.0.
The preconfigured IP address of the IWU in this network is 192.168.2.1.
2. DECT network
Here are all BSIP1 Only Base Stations and the BSIP1 running the HiPath
Cordless IP Server Software (IWU) located. This network is solely used
for the communication of the BSIP1 IWU and the BSIP1 Only.
The preconfigured network address of the BSIP1 IWU is 192.168.1.100
with a netmask of 255.255.255.0.
3. BSIP1 internal networks
For internal communication between the different hardware components
of the BSIP1 there are two further networks configured.
Important: These addresses are fixed and cannot be changed. Keep in
mind, that these addresses may not be used for the VoIP network and the
DECT network.
192.168.123.x :
Network between the BSIP1 Local DECT module (.222) and the BSIP1
IWU (.111).
169.254.222.x.
Network between the two main processors (CSP) and 192.168.123.x
(MSP) for internal communication.
Important: All BSIP1 devices must be located inside the same network
segment and therefore MUST NOT be separated by layer 3 routing devices.
Only Layer 2 switches are supported between the BSIPs.