User's Manual
Table Of Contents
- Contents
- List of Tables
- List of Figures
- 1 Introduction and Important Notes
- 2 Overview
- 3 Planning a HiPath Cordless IP System
- 3.1 Planning According to Call Traffic Load
- 3.2 General
- 3.3 Propagation Conditions for Radio Traffic
- 3.4 Determining the Installation Site
- 3.5 Installing Base Stations
- 4 Putting Into Service
- 5 Installation and Administration
- 5.1 Terminology
- 5.2 Network Concept
- 5.3 Synchronisation over air concept
- 5.4 WBM related issues
- 5.5 Phone related issues
- 5.6 Partition concept of BSIP1
- 5.7 Factory reset of BSIP1
- 5.8 Release notes
- 5.9 Quick Start
- 5.10 Quick start overview
- 5.11 Prepare and connect hardware
- 5.12 Configure BSIP1 for IWU mode
- 5.13 Configuration of VoIP (Infrastructure) network
- 5.14 Configuration of DECT network
- 5.15 Configuration of users at the PBX
- 5.16 Configuration of users at the BSIP IWU
- 5.17 Start system services and register handsets
- 5.18 Configure further BSIP Only to the system
- 5.19 "Quick Start" Completion
- 5.20 Further steps
- 5.21 Configuration reference
- 5.22 WBM overview
- 5.23 Administration
- 5.24 "Network/Gateways" Configuration
- 5.25 "Group" Configuration
- 5.26 Users Configuration
- 5.27 Dect Configuration
- 5.27.1 Configuration Page "Dect - Device"
- 5.27.2 Configuration Page "Dect - Sync"
- 5.27.3 Configuration Page "Dect - ARI"
- 5.27.4 Configuration Page "Dect - About"
- 5.27.5 Configuration Page "Dect - Radio" (Advanced mode)
- 5.27.6 Configuration Page "Dect - Call" (Advanced mode)
- 5.27.7 Configuration Page "Dect - Debug" (Advanced mode)
- 5.27.8 General DECT configuration
- 5.28 Debugging Configuration
- 5.29 "Status" Configuration
- 5.30 "System" Configuration
- 5.31 Configuration Hints for PBXs
- 5.32 HiPath OpenOffice EE
- 5.33 HiPath OpenOffice ME
- 5.34 Troubleshooting / FAQ
- 5.35 Configuration hints for Web Browser
- 6 Technical Data
- 7 Diagnosis and Maintenance
- 8 Open Source Software used in the Product
- Index
Planning a HiPath Cordless IP System
c03.fm
Determining the Installation Site
A31003-C1010-S100-2-7620, 08/2010
44 HiPath Cordless IP, Service Manual
Example: Planning an outdoor area (Figure 13)
NOTE: A base station installed in an attic directly beside a dormer window (no
metal reinforcement in the window pane) is the alternative to outdoor housing for
coverage of the outdoor area.
• Planning
A site plan, for example, with a scale of 1:300 or 1:1000 is helpful for
determining the base station installation site.
– The customer’s preferred radio area should be indicated on the map
(subject to customer confirmation).
– Additional information about the types and heights of buildings is also
helpful.
– Radio coverage can be adequately determined with the aid of the site
plan and the information above.
• Site plan, see Figure 13
This plan depicts a company’s grounds with buildings A to G. It includes the
type of construction and heights of these buildings.
– Bird’s eye perspective
It is relatively simple to find the point which offers the best possible view
of the grounds without any obstructions.
Placement around the buildings C, E, F, and G is not feasible since the
view from these buildings extends only to a few neighboring buildings.
The view from buildings A and B is better.
In the example, the decision was made to place the base station at
building B rather than A. Note that the areas between buildings C and E
as well as F, G, and A are covered. The radio waves can pass through
brick building A, so that an area of about 10 meters beyond will still be
covered.
In practice, coverage can also be assumed for other outdoor areas as waves
pass through the windows.
• Reinforced concrete buildings or constructions with metal facades
act as limiting factors. Areas behind these buildings are quasioptically
blocked and must be considered not covered by the radio waves.
• Brick buildings
can usually be penetrated so that significant parts of them are reached by the
radio waves.
The supply range, however, often stops less than 10 meters beyond these
buildings.