User's Manual
Table Of Contents
- Contents
- List of Tables
- List of Figures
- 1 Introduction and Important Notes
- 2 Overview
- 3 Planning a HiPath Cordless IP System
- 3.1 Planning According to Call Traffic Load
- 3.2 General
- 3.3 Propagation Conditions for Radio Traffic
- 3.4 Determining the Installation Site
- 3.5 Installing Base Stations
- 4 Putting Into Service
- 5 Installation and Administration
- 5.1 Terminology
- 5.2 Network Concept
- 5.3 Synchronisation over air concept
- 5.4 WBM related issues
- 5.5 Phone related issues
- 5.6 Partition concept of BSIP1
- 5.7 Factory reset of BSIP1
- 5.8 Release notes
- 5.9 Quick Start
- 5.10 Quick start overview
- 5.11 Prepare and connect hardware
- 5.12 Configure BSIP1 for IWU mode
- 5.13 Configuration of VoIP (Infrastructure) network
- 5.14 Configuration of DECT network
- 5.15 Configuration of users at the PBX
- 5.16 Configuration of users at the BSIP IWU
- 5.17 Start system services and register handsets
- 5.18 Configure further BSIP Only to the system
- 5.19 "Quick Start" Completion
- 5.20 Further steps
- 5.21 Configuration reference
- 5.22 WBM overview
- 5.23 Administration
- 5.24 "Network/Gateways" Configuration
- 5.25 "Group" Configuration
- 5.26 Users Configuration
- 5.27 Dect Configuration
- 5.27.1 Configuration Page "Dect - Device"
- 5.27.2 Configuration Page "Dect - Sync"
- 5.27.3 Configuration Page "Dect - ARI"
- 5.27.4 Configuration Page "Dect - About"
- 5.27.5 Configuration Page "Dect - Radio" (Advanced mode)
- 5.27.6 Configuration Page "Dect - Call" (Advanced mode)
- 5.27.7 Configuration Page "Dect - Debug" (Advanced mode)
- 5.27.8 General DECT configuration
- 5.28 Debugging Configuration
- 5.29 "Status" Configuration
- 5.30 "System" Configuration
- 5.31 Configuration Hints for PBXs
- 5.32 HiPath OpenOffice EE
- 5.33 HiPath OpenOffice ME
- 5.34 Troubleshooting / FAQ
- 5.35 Configuration hints for Web Browser
- 6 Technical Data
- 7 Diagnosis and Maintenance
- 8 Open Source Software used in the Product
- Index
Planning a HiPath Cordless IP System
c03.fm
Determining the Installation Site
A31003-C1010-S100-2-7620, 08/2010
42 HiPath Cordless IP, Service Manual
3.4.1.3 Factory Halls and Open-Plan Offices
• Within halls or open-plan offices (Figure 10)
Good transmission qualities.
For a hall which is 100 m long, one centrally located base station, suspended
freely from the ceiling (mast, plastic chain), may be sufficient.
7
CAUTION
The base station should not be installed on a reinforced concrete pillar
because the pillar creates a partial shadow which means that a clear line of
sight no longer exists.
In this case, two base stations must be installed 50 m to 75 m apart.
In the case of outer walls or interior siding and/or hall ceilings made of metal
(or metal-clad), it may be necessary to increase the number of base stations
and distribute them in such a way as to virtually exclude radio interference
through reflections.
3.4.2 Outdoors
• Base station with outdoor housing (Figure 12)
Only base stations with weather-resistant housing are suitable for radio
coverage out of doors, e.g. on factory sites.
– Installation
A base station can be installed on a mast made of wood, plastic or
concrete (not metal), on the roof of a building (preferably made of brick or
light construction materials) or on the wall of a house.
– The mast used must be stable and wind-resistant.
NOTE: Choose the installation site to allow maximum visibility from the base
station to the service area.