User's Manual
Table Of Contents
- Contents
- List of Tables
- List of Figures
- 1 Introduction and Important Notes
- 2 Overview
- 3 Planning a HiPath Cordless IP System
- 3.1 Planning According to Call Traffic Load
- 3.2 General
- 3.3 Propagation Conditions for Radio Traffic
- 3.4 Determining the Installation Site
- 3.5 Installing Base Stations
- 4 Putting Into Service
- 5 Installation and Administration
- 5.1 Terminology
- 5.2 Network Concept
- 5.3 Synchronisation over air concept
- 5.4 WBM related issues
- 5.5 Phone related issues
- 5.6 Partition concept of BSIP1
- 5.7 Factory reset of BSIP1
- 5.8 Release notes
- 5.9 Quick Start
- 5.10 Quick start overview
- 5.11 Prepare and connect hardware
- 5.12 Configure BSIP1 for IWU mode
- 5.13 Configuration of VoIP (Infrastructure) network
- 5.14 Configuration of DECT network
- 5.15 Configuration of users at the PBX
- 5.16 Configuration of users at the BSIP IWU
- 5.17 Start system services and register handsets
- 5.18 Configure further BSIP Only to the system
- 5.19 "Quick Start" Completion
- 5.20 Further steps
- 5.21 Configuration reference
- 5.22 WBM overview
- 5.23 Administration
- 5.24 "Network/Gateways" Configuration
- 5.25 "Group" Configuration
- 5.26 Users Configuration
- 5.27 Dect Configuration
- 5.27.1 Configuration Page "Dect - Device"
- 5.27.2 Configuration Page "Dect - Sync"
- 5.27.3 Configuration Page "Dect - ARI"
- 5.27.4 Configuration Page "Dect - About"
- 5.27.5 Configuration Page "Dect - Radio" (Advanced mode)
- 5.27.6 Configuration Page "Dect - Call" (Advanced mode)
- 5.27.7 Configuration Page "Dect - Debug" (Advanced mode)
- 5.27.8 General DECT configuration
- 5.28 Debugging Configuration
- 5.29 "Status" Configuration
- 5.30 "System" Configuration
- 5.31 Configuration Hints for PBXs
- 5.32 HiPath OpenOffice EE
- 5.33 HiPath OpenOffice ME
- 5.34 Troubleshooting / FAQ
- 5.35 Configuration hints for Web Browser
- 6 Technical Data
- 7 Diagnosis and Maintenance
- 8 Open Source Software used in the Product
- Index
c02.fm
Overview
A31003-C1010-S100-2-7620, 08/2010
HiPath Cordless IP, Service Manual 17
2 Overview
The HiPath Cordless IP solution extends the scope of the DECT standard
introduced for voice communication, making it now available for Voice over IP
infrastructures.
The radio range covered by the HiPath Cordless IP system is made up of DECT
IP base stations that together form either an seamless network of overlapping
and synchronous radio cells or individual radio islands. The size of a radio cell
depends on local/structural factors.
Voice over IP infrastructures are connected via the SIP protocol. In their capacity
as mobile communication solutions, DECT radio cells are therefore an optimal
enhancement to SIP-compliant Voice over IP systems.
The DECT IP base stations support seamless handover in ongoing voice
connections, that is, moving from one radio cell to another during a call with a
DECT handset. The roaming function is also available for mobile stations.
HiPath Cordless IP also supports the DECT protocol GAP (Generic Access
Profile) and the radio protocol PN-CAP. The basic function scope required by
ETSI is thus extended to include a number of Siemens-specific features.
Figure 1 General Overview of the HiPath Cordless IP System