User's Manual
Table Of Contents
- Contents
- List of Tables
- List of Figures
- 1 Introduction and Important Notes
- 2 Overview
- 3 Planning a HiPath Cordless IP System
- 3.1 Planning According to Call Traffic Load
- 3.2 General
- 3.3 Propagation Conditions for Radio Traffic
- 3.4 Determining the Installation Site
- 3.5 Installing Base Stations
- 4 Putting Into Service
- 5 Installation and Administration
- 5.1 Terminology
- 5.2 Network Concept
- 5.3 Synchronisation over air concept
- 5.4 WBM related issues
- 5.5 Phone related issues
- 5.6 Partition concept of BSIP1
- 5.7 Factory reset of BSIP1
- 5.8 Release notes
- 5.9 Quick Start
- 5.10 Quick start overview
- 5.11 Prepare and connect hardware
- 5.12 Configure BSIP1 for IWU mode
- 5.13 Configuration of VoIP (Infrastructure) network
- 5.14 Configuration of DECT network
- 5.15 Configuration of users at the PBX
- 5.16 Configuration of users at the BSIP IWU
- 5.17 Start system services and register handsets
- 5.18 Configure further BSIP Only to the system
- 5.19 "Quick Start" Completion
- 5.20 Further steps
- 5.21 Configuration reference
- 5.22 WBM overview
- 5.23 Administration
- 5.24 "Network/Gateways" Configuration
- 5.25 "Group" Configuration
- 5.26 Users Configuration
- 5.27 Dect Configuration
- 5.27.1 Configuration Page "Dect - Device"
- 5.27.2 Configuration Page "Dect - Sync"
- 5.27.3 Configuration Page "Dect - ARI"
- 5.27.4 Configuration Page "Dect - About"
- 5.27.5 Configuration Page "Dect - Radio" (Advanced mode)
- 5.27.6 Configuration Page "Dect - Call" (Advanced mode)
- 5.27.7 Configuration Page "Dect - Debug" (Advanced mode)
- 5.27.8 General DECT configuration
- 5.28 Debugging Configuration
- 5.29 "Status" Configuration
- 5.30 "System" Configuration
- 5.31 Configuration Hints for PBXs
- 5.32 HiPath OpenOffice EE
- 5.33 HiPath OpenOffice ME
- 5.34 Troubleshooting / FAQ
- 5.35 Configuration hints for Web Browser
- 6 Technical Data
- 7 Diagnosis and Maintenance
- 8 Open Source Software used in the Product
- Index
c06.fm
Technical Data
Base Stations
A31003-C1010-S100-2-7620, 08/2010
HiPath Cordless IP, Service Manual 157
6.3.1.3 Gigaset M2 professional, Gigaset M2 plus professional
Do not remove the battery pack without good reason as charge state monitoring
and the recharge function will not work properly if you do! After the batteriey pack
is removed and reinserted, it must be discharged and recharged as for the initial
startup!
7
CAUTION
The use of any other battery packs may cause functional disturbances or
may damage the handsets. The manufacturer will not be held liable in such
cases. If replacement battery packs are required, be sure to use only the
approved types.
• Software Checking, see Section 7.2.2
• Output power Average output power +10 dBm per channel
Peak output power +24 dBm per channel
• Tone ringing
– Volume control adjustable: 5 levels, levels 4 and 5 for loud
environments.
– Tone ringing signal Can be configured separately for internal and
external calls
20 standard ringtones (3 ringtones / 17 melodies)
16 loadable polyphonic melodies
• User Interface (UI) Menu-driven graphic user interface
• Display Illuminated color display
• Telephone book
(integrated locally)
Up to a total of 250 entries
• Voice dialing
(voice telephone book)
Up to 30 entries
• PIN-lock • 4-digit, numeric (see Section 7.3.3)
• Full functionality of device
guaranteed for
-10 °C to +55 °C
100 % relative humidity including splashes and low
pressure jets of water (IP 65)
• Power supply (state of charge indicated on the display)
• Approved battery pack Lithium-Ion, 1000 mAh (A5B00075416005)
Example for a capacity of 850 mAh:
– Talktime Up to 12 hours
– Standby-Time Up to 380 hours, approx. 16 days
– Charging time in handset approx. 3,7 hours
– Initial charging time at least 10 h
• Housing approx. 166,5 x 56,0 x 35,4 mm (L x W x H)