User's Manual
Table Of Contents
- Contents
- List of Tables
- List of Figures
- 1 Introduction and Important Notes
- 2 Overview
- 3 Planning a HiPath Cordless IP System
- 3.1 Planning According to Call Traffic Load
- 3.2 General
- 3.3 Propagation Conditions for Radio Traffic
- 3.4 Determining the Installation Site
- 3.5 Installing Base Stations
- 4 Putting Into Service
- 5 Installation and Administration
- 5.1 Terminology
- 5.2 Network Concept
- 5.3 Synchronisation over air concept
- 5.4 WBM related issues
- 5.5 Phone related issues
- 5.6 Partition concept of BSIP1
- 5.7 Factory reset of BSIP1
- 5.8 Release notes
- 5.9 Quick Start
- 5.10 Quick start overview
- 5.11 Prepare and connect hardware
- 5.12 Configure BSIP1 for IWU mode
- 5.13 Configuration of VoIP (Infrastructure) network
- 5.14 Configuration of DECT network
- 5.15 Configuration of users at the PBX
- 5.16 Configuration of users at the BSIP IWU
- 5.17 Start system services and register handsets
- 5.18 Configure further BSIP Only to the system
- 5.19 "Quick Start" Completion
- 5.20 Further steps
- 5.21 Configuration reference
- 5.22 WBM overview
- 5.23 Administration
- 5.24 "Network/Gateways" Configuration
- 5.25 "Group" Configuration
- 5.26 Users Configuration
- 5.27 Dect Configuration
- 5.27.1 Configuration Page "Dect - Device"
- 5.27.2 Configuration Page "Dect - Sync"
- 5.27.3 Configuration Page "Dect - ARI"
- 5.27.4 Configuration Page "Dect - About"
- 5.27.5 Configuration Page "Dect - Radio" (Advanced mode)
- 5.27.6 Configuration Page "Dect - Call" (Advanced mode)
- 5.27.7 Configuration Page "Dect - Debug" (Advanced mode)
- 5.27.8 General DECT configuration
- 5.28 Debugging Configuration
- 5.29 "Status" Configuration
- 5.30 "System" Configuration
- 5.31 Configuration Hints for PBXs
- 5.32 HiPath OpenOffice EE
- 5.33 HiPath OpenOffice ME
- 5.34 Troubleshooting / FAQ
- 5.35 Configuration hints for Web Browser
- 6 Technical Data
- 7 Diagnosis and Maintenance
- 8 Open Source Software used in the Product
- Index
c06.fm
Technical Data
Base Stations
A31003-C1010-S100-2-7620, 08/2010
HiPath Cordless IP, Service Manual 151
LED status displays on the base station
• No settings need be made at the base station.
• LED 1/LED 2 on the front of the base station provides the following
information:
Operating State LED 1 LED 2
LED status at booting sequence
No power on Base station off off
BSIP1 is booting the the Active partition red
flashing
red
flashing
BSIP1 is booting the the Fallback partition red
flashing
off
BSIP1 is booting the Active partition with factory
defaults
red
fast flashing
red
fast flashing
BSIP1 is booting the Fallback partition with
factory defaults
red
fast flashing
off
BSIP1 is booting kernel with Active partition off red
BSIP1 is booting kernel with Fallback partition red off
LED status at working process
BSIP1 not ready
Services not started or starting
orange orange
BSIP1 ready
No LAN link
red red
BSIP1 ready
No Connection to IWU
green red
BSIP1 ready
All DECT-frequencies blocked or all available
DECT channels occupied
red green
BSIP1 ready
Link unsynchronized (DECT/LAN), no active call
off green
Table 7 LED status displays on the base station