User's Manual
Table Of Contents
- Contents
- List of Tables
- List of Figures
- 1 Introduction and Important Notes
- 2 Overview
- 3 Planning a HiPath Cordless IP System
- 3.1 Planning According to Call Traffic Load
- 3.2 General
- 3.3 Propagation Conditions for Radio Traffic
- 3.4 Determining the Installation Site
- 3.5 Installing Base Stations
- 4 Putting Into Service
- 5 Installation and Administration
- 5.1 Terminology
- 5.2 Network Concept
- 5.3 Synchronisation over air concept
- 5.4 WBM related issues
- 5.5 Phone related issues
- 5.6 Partition concept of BSIP1
- 5.7 Factory reset of BSIP1
- 5.8 Release notes
- 5.9 Quick Start
- 5.10 Quick start overview
- 5.11 Prepare and connect hardware
- 5.12 Configure BSIP1 for IWU mode
- 5.13 Configuration of VoIP (Infrastructure) network
- 5.14 Configuration of DECT network
- 5.15 Configuration of users at the PBX
- 5.16 Configuration of users at the BSIP IWU
- 5.17 Start system services and register handsets
- 5.18 Configure further BSIP Only to the system
- 5.19 "Quick Start" Completion
- 5.20 Further steps
- 5.21 Configuration reference
- 5.22 WBM overview
- 5.23 Administration
- 5.24 "Network/Gateways" Configuration
- 5.25 "Group" Configuration
- 5.26 Users Configuration
- 5.27 Dect Configuration
- 5.27.1 Configuration Page "Dect - Device"
- 5.27.2 Configuration Page "Dect - Sync"
- 5.27.3 Configuration Page "Dect - ARI"
- 5.27.4 Configuration Page "Dect - About"
- 5.27.5 Configuration Page "Dect - Radio" (Advanced mode)
- 5.27.6 Configuration Page "Dect - Call" (Advanced mode)
- 5.27.7 Configuration Page "Dect - Debug" (Advanced mode)
- 5.27.8 General DECT configuration
- 5.28 Debugging Configuration
- 5.29 "Status" Configuration
- 5.30 "System" Configuration
- 5.31 Configuration Hints for PBXs
- 5.32 HiPath OpenOffice EE
- 5.33 HiPath OpenOffice ME
- 5.34 Troubleshooting / FAQ
- 5.35 Configuration hints for Web Browser
- 6 Technical Data
- 7 Diagnosis and Maintenance
- 8 Open Source Software used in the Product
- Index
Technical Data
c06.fm
Base Stations
A31003-C1010-S100-2-7620, 08/2010
150 HiPath Cordless IP, Service Manual
6.3 Base Stations
General
DECT IP Basisstation BSIP1
• Software Can be loaded via the communication system.
• Antennas Two external antennas are mounted on the top of
the housing of the base station.
The base station works with antenna diversity (this
means that the radio receiver is connected to
whichever antenna delivers the greater field
strength).
• Average output power 10 mW to 125 mW
• Radio range Basically dependant on the radio transmission
characteristics of the environment/premises.
– Outdoors Up to 300 m
– Indoors Up to 50 m
• Power supply PoE is used to supply power to the DECT IP base
station
• Accessories Outdoor housing
• Dimensions 202 x 172 x 43 (W x H x D in mm)
• Weight 500 g
• Power supply PoE, according IEEE 802.3af Class 2
• Power consumption < 6,5 W
• Operating temperature indoors
Outdoors (in outdoor housing)
+ 0°C to + 40°C
- 25°C to + 40°C
• Cabling 10/100 Mbps Ethernet cable, Cat. 5 and higher,
8-pin shielded RJ45 connector