User's Manual
Table Of Contents
- Contents
- List of Tables
- List of Figures
- 1 Introduction and Important Notes
- 2 Overview
- 3 Planning a HiPath Cordless IP System
- 3.1 Planning According to Call Traffic Load
- 3.2 General
- 3.3 Propagation Conditions for Radio Traffic
- 3.4 Determining the Installation Site
- 3.5 Installing Base Stations
- 4 Putting Into Service
- 5 Installation and Administration
- 5.1 Terminology
- 5.2 Network Concept
- 5.3 Synchronisation over air concept
- 5.4 WBM related issues
- 5.5 Phone related issues
- 5.6 Partition concept of BSIP1
- 5.7 Factory reset of BSIP1
- 5.8 Release notes
- 5.9 Quick Start
- 5.10 Quick start overview
- 5.11 Prepare and connect hardware
- 5.12 Configure BSIP1 for IWU mode
- 5.13 Configuration of VoIP (Infrastructure) network
- 5.14 Configuration of DECT network
- 5.15 Configuration of users at the PBX
- 5.16 Configuration of users at the BSIP IWU
- 5.17 Start system services and register handsets
- 5.18 Configure further BSIP Only to the system
- 5.19 "Quick Start" Completion
- 5.20 Further steps
- 5.21 Configuration reference
- 5.22 WBM overview
- 5.23 Administration
- 5.24 "Network/Gateways" Configuration
- 5.25 "Group" Configuration
- 5.26 Users Configuration
- 5.27 Dect Configuration
- 5.27.1 Configuration Page "Dect - Device"
- 5.27.2 Configuration Page "Dect - Sync"
- 5.27.3 Configuration Page "Dect - ARI"
- 5.27.4 Configuration Page "Dect - About"
- 5.27.5 Configuration Page "Dect - Radio" (Advanced mode)
- 5.27.6 Configuration Page "Dect - Call" (Advanced mode)
- 5.27.7 Configuration Page "Dect - Debug" (Advanced mode)
- 5.27.8 General DECT configuration
- 5.28 Debugging Configuration
- 5.29 "Status" Configuration
- 5.30 "System" Configuration
- 5.31 Configuration Hints for PBXs
- 5.32 HiPath OpenOffice EE
- 5.33 HiPath OpenOffice ME
- 5.34 Troubleshooting / FAQ
- 5.35 Configuration hints for Web Browser
- 6 Technical Data
- 7 Diagnosis and Maintenance
- 8 Open Source Software used in the Product
- Index
c05_ikon.fm
Installation and Administration
HiPath OpenOffice ME
A31003-C1010-S100-2-7620, 08/2010
HiPath Cordless IP, Service Manual 141
5.33.3 Station Configuration - HiPath OpenOffice ME
The following values are used as a sample for this configuration instruction:
1. The configuration of the HiPath OpenOffice ME is done via Web browser
(Web Based Management - WBM). Please log in to the HiPath
OpenOffice ME, start the Web Based Management in Expert mode and
navigate to the page "WBM - Expert mode - Station - IP Clients - SIP
Clients".
2. Select a free entry (after the base configuration of the Siemens HiPath
OpenOffice ME with the Assistant free entries should be available).
If no free entries are available, use the page "WBM - Expert mode -
Stations - Station - IP Clients - Edit subscriber", change the "Device Type"
of a free entry to "SIP Client" and store the modifications with [Apply].
Now a free SIP User should be available on "WBM - Explorers - Stations
- Station - IP Clients - SIP Clients".
5.33.3.1 Step 1 - User Parameters
1. Select the free entry and choose "Edit station parameter". Enter the
following values in the input mask:
Please do not change the other values. After that the configuration page
should look like this:
Parameter Value
Name DECT-401
Callnumber 401
Password ikon
Entry Value
Callnumber: 401
Name: DECT-401
Direct inward dialing: 401