User's Manual
Table Of Contents
- Contents
- List of Tables
- List of Figures
- 1 Introduction and Important Notes
- 2 Overview
- 3 Planning a HiPath Cordless IP System
- 3.1 Planning According to Call Traffic Load
- 3.2 General
- 3.3 Propagation Conditions for Radio Traffic
- 3.4 Determining the Installation Site
- 3.5 Installing Base Stations
- 4 Putting Into Service
- 5 Installation and Administration
- 5.1 Terminology
- 5.2 Network Concept
- 5.3 Synchronisation over air concept
- 5.4 WBM related issues
- 5.5 Phone related issues
- 5.6 Partition concept of BSIP1
- 5.7 Factory reset of BSIP1
- 5.8 Release notes
- 5.9 Quick Start
- 5.10 Quick start overview
- 5.11 Prepare and connect hardware
- 5.12 Configure BSIP1 for IWU mode
- 5.13 Configuration of VoIP (Infrastructure) network
- 5.14 Configuration of DECT network
- 5.15 Configuration of users at the PBX
- 5.16 Configuration of users at the BSIP IWU
- 5.17 Start system services and register handsets
- 5.18 Configure further BSIP Only to the system
- 5.19 "Quick Start" Completion
- 5.20 Further steps
- 5.21 Configuration reference
- 5.22 WBM overview
- 5.23 Administration
- 5.24 "Network/Gateways" Configuration
- 5.25 "Group" Configuration
- 5.26 Users Configuration
- 5.27 Dect Configuration
- 5.27.1 Configuration Page "Dect - Device"
- 5.27.2 Configuration Page "Dect - Sync"
- 5.27.3 Configuration Page "Dect - ARI"
- 5.27.4 Configuration Page "Dect - About"
- 5.27.5 Configuration Page "Dect - Radio" (Advanced mode)
- 5.27.6 Configuration Page "Dect - Call" (Advanced mode)
- 5.27.7 Configuration Page "Dect - Debug" (Advanced mode)
- 5.27.8 General DECT configuration
- 5.28 Debugging Configuration
- 5.29 "Status" Configuration
- 5.30 "System" Configuration
- 5.31 Configuration Hints for PBXs
- 5.32 HiPath OpenOffice EE
- 5.33 HiPath OpenOffice ME
- 5.34 Troubleshooting / FAQ
- 5.35 Configuration hints for Web Browser
- 6 Technical Data
- 7 Diagnosis and Maintenance
- 8 Open Source Software used in the Product
- Index
Installation and Administration
c05_ikon.fm
HiPath OpenOffice ME
A31003-C1010-S100-2-7620, 08/2010
138 HiPath Cordless IP, Service Manual
5.32.5 Time server configuration
1. Configure the following settings to activate the time server settings via
“WBM - Explorers - Basic Settings - Date and Time - SNTP settings“:
2. Save the modifications by clicking [Apply].
5.33 HiPath OpenOffice ME
Here you can find the configuration hints using a HiPath OpenOffice ME (SW-
Version V1) using SIP users.
5.33.1 Base Configuration - HiPath OpenOffice ME
• The following value is used for the base configuration:
Detailed configuration instruction for the HiPath OpenOffice ME would go
beyond the scope of this documentation. Therefore only the information
regarding the configuration which is very important and relevant for the Inter-
working is described here.
Detailed documentation for the HiPath OpenOffice ME can be found in the
Siemens manuals:
• "HiPath OpenOffice ME V1 Administrator Documentation"
Entry Value
operating state of SNTP Server: Up
IP address of External Time Server IP adress: 0.0.0.0 if no external time server
is used for time synchronisation, otherwise
the ip address of the external time server.
Poll interval for External Time Server Continuous
Parameter Value
IP address of the HiPath OpenOffice ME 192.168.0.93