User's Manual
Table Of Contents
- Contents
- List of Tables
- List of Figures
- 1 Introduction and Important Notes
- 2 Overview
- 3 Planning a HiPath Cordless IP System
- 3.1 Planning According to Call Traffic Load
- 3.2 General
- 3.3 Propagation Conditions for Radio Traffic
- 3.4 Determining the Installation Site
- 3.5 Installing Base Stations
- 4 Putting Into Service
- 5 Installation and Administration
- 5.1 Terminology
- 5.2 Network Concept
- 5.3 Synchronisation over air concept
- 5.4 WBM related issues
- 5.5 Phone related issues
- 5.6 Partition concept of BSIP1
- 5.7 Factory reset of BSIP1
- 5.8 Release notes
- 5.9 Quick Start
- 5.10 Quick start overview
- 5.11 Prepare and connect hardware
- 5.12 Configure BSIP1 for IWU mode
- 5.13 Configuration of VoIP (Infrastructure) network
- 5.14 Configuration of DECT network
- 5.15 Configuration of users at the PBX
- 5.16 Configuration of users at the BSIP IWU
- 5.17 Start system services and register handsets
- 5.18 Configure further BSIP Only to the system
- 5.19 "Quick Start" Completion
- 5.20 Further steps
- 5.21 Configuration reference
- 5.22 WBM overview
- 5.23 Administration
- 5.24 "Network/Gateways" Configuration
- 5.25 "Group" Configuration
- 5.26 Users Configuration
- 5.27 Dect Configuration
- 5.27.1 Configuration Page "Dect - Device"
- 5.27.2 Configuration Page "Dect - Sync"
- 5.27.3 Configuration Page "Dect - ARI"
- 5.27.4 Configuration Page "Dect - About"
- 5.27.5 Configuration Page "Dect - Radio" (Advanced mode)
- 5.27.6 Configuration Page "Dect - Call" (Advanced mode)
- 5.27.7 Configuration Page "Dect - Debug" (Advanced mode)
- 5.27.8 General DECT configuration
- 5.28 Debugging Configuration
- 5.29 "Status" Configuration
- 5.30 "System" Configuration
- 5.31 Configuration Hints for PBXs
- 5.32 HiPath OpenOffice EE
- 5.33 HiPath OpenOffice ME
- 5.34 Troubleshooting / FAQ
- 5.35 Configuration hints for Web Browser
- 6 Technical Data
- 7 Diagnosis and Maintenance
- 8 Open Source Software used in the Product
- Index
c05_ikon.fm
Installation and Administration
HiPath OpenOffice EE
A31003-C1010-S100-2-7620, 08/2010
HiPath Cordless IP, Service Manual 135
5.32.2 Base Configuration - BSIP IWU
Please make the following configuration settings at the BSIP IWU:
1. Page "Network/Gateways", table gateways
2. Save all modifications with [Apply].
3. Configure one DECT ethernet Base Station for the operation with this
Gateway.
5.32.3 Station Configuration - HiPath OpenOffice EE
The following values are used as a sample for this configuration instruction:
1. The configuration of the HiPath OpenOffice EE is done via Web browser
(Web Based Management - WBM). Please log in to the HiPath
OpenOffice EE, start the Web Based Management in Expert mode and
navigate to the page "WBM - Explorers - Stations - Station - IP Clients -
SIP Clients".
2. Select a free entry (after the base configuration of the
HiPath OpenOffice EE with the assistant free entries should be
available).
If no free entries are available, use the "Subscriber table editor" on the
page "WBM - Explorers - Stations - Station - (Right mouse button ) -
Subscriber table editor", change the "Device Type" of a free entry to "SIP
Client" and store the modifications with [Apply]. After that you should
store the new configuration on the HiPath with the [Save] Button at the
bottom section of the WBM. Now a free SIP User should be available on
"WBM - Explorers - Stations - Station - IP Clients - SIP Clients".
Option Value
Remote IP Address 192.168.0.213
Gatekeeper Id 192.168.0.213
Parameter Value
Name DECT-401
Callnumber 401
Password ikon