User's Manual
Table Of Contents
- Contents
- List of Tables
- List of Figures
- 1 Introduction and Important Notes
- 2 Overview
- 3 Planning a HiPath Cordless IP System
- 3.1 Planning According to Call Traffic Load
- 3.2 General
- 3.3 Propagation Conditions for Radio Traffic
- 3.4 Determining the Installation Site
- 3.5 Installing Base Stations
- 4 Putting Into Service
- 5 Installation and Administration
- 5.1 Terminology
- 5.2 Network Concept
- 5.3 Synchronisation over air concept
- 5.4 WBM related issues
- 5.5 Phone related issues
- 5.6 Partition concept of BSIP1
- 5.7 Factory reset of BSIP1
- 5.8 Release notes
- 5.9 Quick Start
- 5.10 Quick start overview
- 5.11 Prepare and connect hardware
- 5.12 Configure BSIP1 for IWU mode
- 5.13 Configuration of VoIP (Infrastructure) network
- 5.14 Configuration of DECT network
- 5.15 Configuration of users at the PBX
- 5.16 Configuration of users at the BSIP IWU
- 5.17 Start system services and register handsets
- 5.18 Configure further BSIP Only to the system
- 5.19 "Quick Start" Completion
- 5.20 Further steps
- 5.21 Configuration reference
- 5.22 WBM overview
- 5.23 Administration
- 5.24 "Network/Gateways" Configuration
- 5.25 "Group" Configuration
- 5.26 Users Configuration
- 5.27 Dect Configuration
- 5.27.1 Configuration Page "Dect - Device"
- 5.27.2 Configuration Page "Dect - Sync"
- 5.27.3 Configuration Page "Dect - ARI"
- 5.27.4 Configuration Page "Dect - About"
- 5.27.5 Configuration Page "Dect - Radio" (Advanced mode)
- 5.27.6 Configuration Page "Dect - Call" (Advanced mode)
- 5.27.7 Configuration Page "Dect - Debug" (Advanced mode)
- 5.27.8 General DECT configuration
- 5.28 Debugging Configuration
- 5.29 "Status" Configuration
- 5.30 "System" Configuration
- 5.31 Configuration Hints for PBXs
- 5.32 HiPath OpenOffice EE
- 5.33 HiPath OpenOffice ME
- 5.34 Troubleshooting / FAQ
- 5.35 Configuration hints for Web Browser
- 6 Technical Data
- 7 Diagnosis and Maintenance
- 8 Open Source Software used in the Product
- Index
c05_ikon.fm
Installation and Administration
Configuration Hints for PBXs
A31003-C1010-S100-2-7620, 08/2010
HiPath Cordless IP, Service Manual 133
Up since
Displays the time the service was started lastt
"Service"
Usually both services are activated which means that the corresponding
process is started automatically after rebooting the BSIP.
5.31 Configuration Hints for PBXs
In the following chapters you can find configuration notes for for different
PBXs which have to be released for usage with the HiPath Cordless IP
system.
5.32 HiPath OpenOffice EE
Here you can find the configuration hints using a HiPath OpenOffice EE (SW-
Version V1) using SIP users.
5.32.1 Base Configuration - HiPath OpenOffice EE
The following value is used for the base configuration:
A detailed configuration instruction for the HiPath OpenOffice EE would go
beyond the scope of this documentation. Therefore only the information
regarding the configuration which is very important and relevant for the Inter-
working is described here.
Detailed documentation for the HiPath OpenOffice EE can be found in the
manual:
• "HiPath OpenOffice EE V1 Administratior Documentation"
1. Please configure the HiPath OpenOffice EE for the usage with SIP Users
and configure the needed number of SIP Users in the Installation
Assistant.
2. Configure the IP address of the HiPath OpenOffice EE to 192.168.0.213
or change the according IP addresses.
3. Configure the following Codec Parameters via "WBM - Explorers - Voice
Gateway - Codec Parameters":
Parameter Value
IP address of the HiPath OpenOffice EE 192.168.0.213