User's Manual
Table Of Contents
- Contents
- List of Tables
- List of Figures
- 1 Introduction and Important Notes
- 2 Overview
- 3 Planning a HiPath Cordless IP System
- 3.1 Planning According to Call Traffic Load
- 3.2 General
- 3.3 Propagation Conditions for Radio Traffic
- 3.4 Determining the Installation Site
- 3.5 Installing Base Stations
- 4 Putting Into Service
- 5 Installation and Administration
- 5.1 Terminology
- 5.2 Network Concept
- 5.3 Synchronisation over air concept
- 5.4 WBM related issues
- 5.5 Phone related issues
- 5.6 Partition concept of BSIP1
- 5.7 Factory reset of BSIP1
- 5.8 Release notes
- 5.9 Quick Start
- 5.10 Quick start overview
- 5.11 Prepare and connect hardware
- 5.12 Configure BSIP1 for IWU mode
- 5.13 Configuration of VoIP (Infrastructure) network
- 5.14 Configuration of DECT network
- 5.15 Configuration of users at the PBX
- 5.16 Configuration of users at the BSIP IWU
- 5.17 Start system services and register handsets
- 5.18 Configure further BSIP Only to the system
- 5.19 "Quick Start" Completion
- 5.20 Further steps
- 5.21 Configuration reference
- 5.22 WBM overview
- 5.23 Administration
- 5.24 "Network/Gateways" Configuration
- 5.25 "Group" Configuration
- 5.26 Users Configuration
- 5.27 Dect Configuration
- 5.27.1 Configuration Page "Dect - Device"
- 5.27.2 Configuration Page "Dect - Sync"
- 5.27.3 Configuration Page "Dect - ARI"
- 5.27.4 Configuration Page "Dect - About"
- 5.27.5 Configuration Page "Dect - Radio" (Advanced mode)
- 5.27.6 Configuration Page "Dect - Call" (Advanced mode)
- 5.27.7 Configuration Page "Dect - Debug" (Advanced mode)
- 5.27.8 General DECT configuration
- 5.28 Debugging Configuration
- 5.29 "Status" Configuration
- 5.30 "System" Configuration
- 5.31 Configuration Hints for PBXs
- 5.32 HiPath OpenOffice EE
- 5.33 HiPath OpenOffice ME
- 5.34 Troubleshooting / FAQ
- 5.35 Configuration hints for Web Browser
- 6 Technical Data
- 7 Diagnosis and Maintenance
- 8 Open Source Software used in the Product
- Index
c05_ikon.fm
Installation and Administration
Debugging Configuration
A31003-C1010-S100-2-7620, 08/2010
HiPath Cordless IP, Service Manual 123
BSIP1 Debugging messages are logged to a configurable syslog daemon
with Facility="LOCAL1" and SEVERTIY Level="ALERT".
Syslog Server IP
The ip address of the syslog server is configured here.
Logfile Size Total
Displays the limit of the the maximum allocated disk space in bytes for all log
files (stored in the “Log Path”) here. A process checks periodically if the total
size is reached. If the limit is reached the oldest Log Files are deleted to free
up disk space.
Logfile Size
Displays the limit of the the maximum file size in bytes of a single logfile here.
As soon as this size is reached the log output is continued in a new file.
LogPath All
Displays the LogPath the files are stored on the BSIP1.
Download logfiles
With this Button all logfiles of the BSIP can be downloaded and stored on the
file system of the maintenance PC.
1. After clicking on the button [Download logfiles], an browser based file
open dialog will be displayed immediately.
2. You have to select the store method of the dialog, click on button [OK]
and select from the following "save as" dialog a folder to store the confi-
guration files on the maintenance PC or a directory available via the
network.