User's Manual
Table Of Contents
- Contents
- List of Tables
- List of Figures
- 1 Introduction and Important Notes
- 2 Overview
- 3 Planning a HiPath Cordless IP System
- 3.1 Planning According to Call Traffic Load
- 3.2 General
- 3.3 Propagation Conditions for Radio Traffic
- 3.4 Determining the Installation Site
- 3.5 Installing Base Stations
- 4 Putting Into Service
- 5 Installation and Administration
- 5.1 Terminology
- 5.2 Network Concept
- 5.3 Synchronisation over air concept
- 5.4 WBM related issues
- 5.5 Phone related issues
- 5.6 Partition concept of BSIP1
- 5.7 Factory reset of BSIP1
- 5.8 Release notes
- 5.9 Quick Start
- 5.10 Quick start overview
- 5.11 Prepare and connect hardware
- 5.12 Configure BSIP1 for IWU mode
- 5.13 Configuration of VoIP (Infrastructure) network
- 5.14 Configuration of DECT network
- 5.15 Configuration of users at the PBX
- 5.16 Configuration of users at the BSIP IWU
- 5.17 Start system services and register handsets
- 5.18 Configure further BSIP Only to the system
- 5.19 "Quick Start" Completion
- 5.20 Further steps
- 5.21 Configuration reference
- 5.22 WBM overview
- 5.23 Administration
- 5.24 "Network/Gateways" Configuration
- 5.25 "Group" Configuration
- 5.26 Users Configuration
- 5.27 Dect Configuration
- 5.27.1 Configuration Page "Dect - Device"
- 5.27.2 Configuration Page "Dect - Sync"
- 5.27.3 Configuration Page "Dect - ARI"
- 5.27.4 Configuration Page "Dect - About"
- 5.27.5 Configuration Page "Dect - Radio" (Advanced mode)
- 5.27.6 Configuration Page "Dect - Call" (Advanced mode)
- 5.27.7 Configuration Page "Dect - Debug" (Advanced mode)
- 5.27.8 General DECT configuration
- 5.28 Debugging Configuration
- 5.29 "Status" Configuration
- 5.30 "System" Configuration
- 5.31 Configuration Hints for PBXs
- 5.32 HiPath OpenOffice EE
- 5.33 HiPath OpenOffice ME
- 5.34 Troubleshooting / FAQ
- 5.35 Configuration hints for Web Browser
- 6 Technical Data
- 7 Diagnosis and Maintenance
- 8 Open Source Software used in the Product
- Index
Installation and Administration
c05_ikon.fm
Dect Configuration
A31003-C1010-S100-2-7620, 08/2010
118 HiPath Cordless IP, Service Manual
5.27.7 Configuration Page "Dect - Debug" (Advanced
mode)
This page is only displayed in Siemens Admin mode at the WBM.
On the sub page "Debug" various logging and debugging functions may be
activated for the individual DECT modules. Based on these functions
potential problems in the DECT section may be isolated. For the analysis of
the Log files profound knowledge of the DECT technologies is essential.
Therefore debugging is intended primarily for our support staff.
• Note: Please note that depending on the activated Logging configuration
big amounts of data may be produced which may have negative influence
on the performance of the IWU Software and the System. Therefore you
should only activate Logging functions when requested by a support
engineer.
The columns of the configuration page have the following meaning:
• Note: The columns "Enabled" and "Name" are repeated on all sub pages.
A description of these can be found in chapter 5.27.1, “Configuration
Page "Dect - Device"”.
Debug Disable (Default value: Deactivated)
When activating this entry ( ) the Logging functionality for the active DECT
module is disabled, independent of the configured Debug level.
Debug Lvl (Default value: "0x00000000")
Debug level of the selected entry. The value may be entered directly
hexadecimal or via the checkboxes on the right.
5.27.8 General DECT configuration
The configuration page "Dect" is divided into two parts.
In the table view at the top, all BSIP1 modules are configured.
At the bottom of the page, the general DECT configuration of the DECT
Network is done.
• All changes will be activated after a reboot of the BSIP1.