User's Manual
Table Of Contents
- Contents
- List of Tables
- List of Figures
- 1 Introduction and Important Notes
- 2 Overview
- 3 Planning a HiPath Cordless IP System
- 3.1 Planning According to Call Traffic Load
- 3.2 General
- 3.3 Propagation Conditions for Radio Traffic
- 3.4 Determining the Installation Site
- 3.5 Installing Base Stations
- 4 Putting Into Service
- 5 Installation and Administration
- 5.1 Terminology
- 5.2 Network Concept
- 5.3 Synchronisation over air concept
- 5.4 WBM related issues
- 5.5 Phone related issues
- 5.6 Partition concept of BSIP1
- 5.7 Factory reset of BSIP1
- 5.8 Release notes
- 5.9 Quick Start
- 5.10 Quick start overview
- 5.11 Prepare and connect hardware
- 5.12 Configure BSIP1 for IWU mode
- 5.13 Configuration of VoIP (Infrastructure) network
- 5.14 Configuration of DECT network
- 5.15 Configuration of users at the PBX
- 5.16 Configuration of users at the BSIP IWU
- 5.17 Start system services and register handsets
- 5.18 Configure further BSIP Only to the system
- 5.19 "Quick Start" Completion
- 5.20 Further steps
- 5.21 Configuration reference
- 5.22 WBM overview
- 5.23 Administration
- 5.24 "Network/Gateways" Configuration
- 5.25 "Group" Configuration
- 5.26 Users Configuration
- 5.27 Dect Configuration
- 5.27.1 Configuration Page "Dect - Device"
- 5.27.2 Configuration Page "Dect - Sync"
- 5.27.3 Configuration Page "Dect - ARI"
- 5.27.4 Configuration Page "Dect - About"
- 5.27.5 Configuration Page "Dect - Radio" (Advanced mode)
- 5.27.6 Configuration Page "Dect - Call" (Advanced mode)
- 5.27.7 Configuration Page "Dect - Debug" (Advanced mode)
- 5.27.8 General DECT configuration
- 5.28 Debugging Configuration
- 5.29 "Status" Configuration
- 5.30 "System" Configuration
- 5.31 Configuration Hints for PBXs
- 5.32 HiPath OpenOffice EE
- 5.33 HiPath OpenOffice ME
- 5.34 Troubleshooting / FAQ
- 5.35 Configuration hints for Web Browser
- 6 Technical Data
- 7 Diagnosis and Maintenance
- 8 Open Source Software used in the Product
- Index
c05_ikon.fm
Installation and Administration
Users Configuration
A31003-C1010-S100-2-7620, 08/2010
HiPath Cordless IP, Service Manual 109
Password
Enter the Password here which is needed for the registration of the User
(together with the "AuthName").
G729
The usage of low bandwith codec G729 is intended for devices which are
connected to the PBX via low bandwith lines (DSL) e.g. for home office users
using a SIP phone (e.g OptiPoint). Therefore bandwith is an issue for such
scenarios. Inside the LAN efficient bandwith should not be an issue; therefore
codec G711 should generally be used. Therefore there is no need to
configure G729 in the codec list of the PBXs “Gateway - Codec” configuration
page. Activating the codec G729 at the handset changes the codec list from
G711A, G711U to G729ab;G711A,G711U.
To establish a G729 voice connection between a BSIP1 handset (G729
Enabled) and an OptiPoint SIP phone, the following configuration is
necessary:
At the BSIP1, configure G729 for the desired or all user.
At the SIP phone, configure the speech codecs for “G729 preferred” and
activate “Silence suppression” (Silence Supression is needed due to the used
“b” variant of the G729 codec).
Using these settings, calls between the following participiants should use the
following codec:
5.26.4 Configuration Page "User - Dect"
This page contains the user configuration for DECT.
• Note: The columns "Index", "Enabled", "Msn", "DisplayName" and
"Comment" are repeated on all sub pages. A description of these
parameters can be found inchapter 5.26.2, “Configuration Page "User -
User"”.
From / To BSIP1
G729 Enabled
BSIP1
G729 Disabled
SIP phone TDM user
BSIP1
G729 Enabled
G711 G711 G729 G711
BSIP1
G729 Disabled
G711 G711 G711 G711