User's Manual
Table Of Contents
- Contents
- List of Tables
- List of Figures
- 1 Introduction and Important Notes
- 2 Overview
- 3 Planning a HiPath Cordless IP System
- 3.1 Planning According to Call Traffic Load
- 3.2 General
- 3.3 Propagation Conditions for Radio Traffic
- 3.4 Determining the Installation Site
- 3.5 Installing Base Stations
- 4 Putting Into Service
- 5 Installation and Administration
- 5.1 Terminology
- 5.2 Network Concept
- 5.3 Synchronisation over air concept
- 5.4 WBM related issues
- 5.5 Phone related issues
- 5.6 Partition concept of BSIP1
- 5.7 Factory reset of BSIP1
- 5.8 Release notes
- 5.9 Quick Start
- 5.10 Quick start overview
- 5.11 Prepare and connect hardware
- 5.12 Configure BSIP1 for IWU mode
- 5.13 Configuration of VoIP (Infrastructure) network
- 5.14 Configuration of DECT network
- 5.15 Configuration of users at the PBX
- 5.16 Configuration of users at the BSIP IWU
- 5.17 Start system services and register handsets
- 5.18 Configure further BSIP Only to the system
- 5.19 "Quick Start" Completion
- 5.20 Further steps
- 5.21 Configuration reference
- 5.22 WBM overview
- 5.23 Administration
- 5.24 "Network/Gateways" Configuration
- 5.25 "Group" Configuration
- 5.26 Users Configuration
- 5.27 Dect Configuration
- 5.27.1 Configuration Page "Dect - Device"
- 5.27.2 Configuration Page "Dect - Sync"
- 5.27.3 Configuration Page "Dect - ARI"
- 5.27.4 Configuration Page "Dect - About"
- 5.27.5 Configuration Page "Dect - Radio" (Advanced mode)
- 5.27.6 Configuration Page "Dect - Call" (Advanced mode)
- 5.27.7 Configuration Page "Dect - Debug" (Advanced mode)
- 5.27.8 General DECT configuration
- 5.28 Debugging Configuration
- 5.29 "Status" Configuration
- 5.30 "System" Configuration
- 5.31 Configuration Hints for PBXs
- 5.32 HiPath OpenOffice EE
- 5.33 HiPath OpenOffice ME
- 5.34 Troubleshooting / FAQ
- 5.35 Configuration hints for Web Browser
- 6 Technical Data
- 7 Diagnosis and Maintenance
- 8 Open Source Software used in the Product
- Index
Installation and Administration
c05_ikon.fm
Users Configuration
A31003-C1010-S100-2-7620, 08/2010
108 HiPath Cordless IP, Service Manual
Comment
The field "Comment" serves only as a reference for the system administrator
of the BSIP1. It may e.g. contain the type of the Handset or the name of the
department if the Handset is not associated directly to a person.
This field has no influence on the functionality of the IWU.
Language
The language used for display messages of the handset is selected here.
Groups
Choose a Group (and therefore an associated VoIP gateway) from the
dropdown box to which the user is associated to.
5.26.3 Configuration Page "User - VoiP"
On this page the parameters for the registration of the User at the PBX and
the assignment of the subscriber numbers can be configured.
The columns of the configuration page have the following meaning:
• Note: The columns "Index", "Enabled", "Msn", "DisplayName" and
"Comment" are repeated on all sub pages. A description of these
parameters can be found in chapter 5.26.2, “Configuration Page "User -
User"”.
For the correlation between the values used in the VoIP gateway configu-
ration and in WBM see the corresponding chapter for the used PBX in
chapter 5.31, “Configuration Hints for PBXs”.
UserName
Assign a User Name which is used for the registration at the PBX. This may
be a name or a number depending on the PBX or the provider. For the
supported gateways the phonenumber should be used.
AuthName
The authentication Name is needed as a “Login” name if the registration is
done via “RAS” and the account at the PBX is password protected.