User's Manual
Table Of Contents
- Contents
- List of Tables
- List of Figures
- 1 Introduction and Important Notes
- 2 Overview
- 3 Planning a HiPath Cordless IP System
- 3.1 Planning According to Call Traffic Load
- 3.2 General
- 3.3 Propagation Conditions for Radio Traffic
- 3.4 Determining the Installation Site
- 3.5 Installing Base Stations
- 4 Putting Into Service
- 5 Installation and Administration
- 5.1 Terminology
- 5.2 Network Concept
- 5.3 Synchronisation over air concept
- 5.4 WBM related issues
- 5.5 Phone related issues
- 5.6 Partition concept of BSIP1
- 5.7 Factory reset of BSIP1
- 5.8 Release notes
- 5.9 Quick Start
- 5.10 Quick start overview
- 5.11 Prepare and connect hardware
- 5.12 Configure BSIP1 for IWU mode
- 5.13 Configuration of VoIP (Infrastructure) network
- 5.14 Configuration of DECT network
- 5.15 Configuration of users at the PBX
- 5.16 Configuration of users at the BSIP IWU
- 5.17 Start system services and register handsets
- 5.18 Configure further BSIP Only to the system
- 5.19 "Quick Start" Completion
- 5.20 Further steps
- 5.21 Configuration reference
- 5.22 WBM overview
- 5.23 Administration
- 5.24 "Network/Gateways" Configuration
- 5.25 "Group" Configuration
- 5.26 Users Configuration
- 5.27 Dect Configuration
- 5.27.1 Configuration Page "Dect - Device"
- 5.27.2 Configuration Page "Dect - Sync"
- 5.27.3 Configuration Page "Dect - ARI"
- 5.27.4 Configuration Page "Dect - About"
- 5.27.5 Configuration Page "Dect - Radio" (Advanced mode)
- 5.27.6 Configuration Page "Dect - Call" (Advanced mode)
- 5.27.7 Configuration Page "Dect - Debug" (Advanced mode)
- 5.27.8 General DECT configuration
- 5.28 Debugging Configuration
- 5.29 "Status" Configuration
- 5.30 "System" Configuration
- 5.31 Configuration Hints for PBXs
- 5.32 HiPath OpenOffice EE
- 5.33 HiPath OpenOffice ME
- 5.34 Troubleshooting / FAQ
- 5.35 Configuration hints for Web Browser
- 6 Technical Data
- 7 Diagnosis and Maintenance
- 8 Open Source Software used in the Product
- Index
c05_ikon.fm
Installation and Administration
Users Configuration
A31003-C1010-S100-2-7620, 08/2010
HiPath Cordless IP, Service Manual 107
•Hint: The functionality [Delete user] does not remove the registration of
the handset. It only removes the user entry from the WBM configuration.
Therefore if you delete an user, an “Auto entry” will be added later (for
details refer to chapter 5.26.5, “Auto Entry users”.
The buttons [Register], [Remove], [Testcall] and [Hangup] are described at
a later chapter.
5.26.2 Configuration Page "User - User"
On this page the VoIP parameters for the Users are configured.
The columns of the configuration table have the following meaning:
Index
Current number of the User entry. Automatically incremented by the BSIP.
Enabled
When activating this element ( ) the selected User is enabled at the BSIP
IWU.
MSN
The "MSN" should correspond with the Subscriber Number of the User at the
PBX (usually the "User Name" in the PBX).
DisplayName
The handsets will display this value in their idle display. The activation of the
DisplayInfo is done by an outgoing or incoming call. There is neither an
activation of the DisplayInfo due to a Power cycle of the handset nor to a
roaming process.
The DisplayInfo at the handset is limited to a maximum of 10 Characters.
• Important note: Don't use characters others than 0-9, a-z, A-Z, "-" "_" for
the DisplayInfo configuration. Other characters may prevent that the
DisplayInfo is diplayed correctly or that the system services are running
correctly.
To avoid confusions, the field "DisplayName" should be equal the Msn confi-
gured above.