User's Manual
Table Of Contents
- Contents
- List of Tables
- List of Figures
- 1 Introduction and Important Notes
- 2 Overview
- 3 Planning a HiPath Cordless IP System
- 3.1 Planning According to Call Traffic Load
- 3.2 General
- 3.3 Propagation Conditions for Radio Traffic
- 3.4 Determining the Installation Site
- 3.5 Installing Base Stations
- 4 Putting Into Service
- 5 Installation and Administration
- 5.1 Terminology
- 5.2 Network Concept
- 5.3 Synchronisation over air concept
- 5.4 WBM related issues
- 5.5 Phone related issues
- 5.6 Partition concept of BSIP1
- 5.7 Factory reset of BSIP1
- 5.8 Release notes
- 5.9 Quick Start
- 5.10 Quick start overview
- 5.11 Prepare and connect hardware
- 5.12 Configure BSIP1 for IWU mode
- 5.13 Configuration of VoIP (Infrastructure) network
- 5.14 Configuration of DECT network
- 5.15 Configuration of users at the PBX
- 5.16 Configuration of users at the BSIP IWU
- 5.17 Start system services and register handsets
- 5.18 Configure further BSIP Only to the system
- 5.19 "Quick Start" Completion
- 5.20 Further steps
- 5.21 Configuration reference
- 5.22 WBM overview
- 5.23 Administration
- 5.24 "Network/Gateways" Configuration
- 5.25 "Group" Configuration
- 5.26 Users Configuration
- 5.27 Dect Configuration
- 5.27.1 Configuration Page "Dect - Device"
- 5.27.2 Configuration Page "Dect - Sync"
- 5.27.3 Configuration Page "Dect - ARI"
- 5.27.4 Configuration Page "Dect - About"
- 5.27.5 Configuration Page "Dect - Radio" (Advanced mode)
- 5.27.6 Configuration Page "Dect - Call" (Advanced mode)
- 5.27.7 Configuration Page "Dect - Debug" (Advanced mode)
- 5.27.8 General DECT configuration
- 5.28 Debugging Configuration
- 5.29 "Status" Configuration
- 5.30 "System" Configuration
- 5.31 Configuration Hints for PBXs
- 5.32 HiPath OpenOffice EE
- 5.33 HiPath OpenOffice ME
- 5.34 Troubleshooting / FAQ
- 5.35 Configuration hints for Web Browser
- 6 Technical Data
- 7 Diagnosis and Maintenance
- 8 Open Source Software used in the Product
- Index
Installation and Administration
c05_ikon.fm
"Network/Gateways" Configuration
A31003-C1010-S100-2-7620, 08/2010
102 HiPath Cordless IP, Service Manual
The IP address of the gateway inside the VoIP (Infrastructure) network which
handles the routing to the other network.
HTTPS Enable
Determines if https (Hypertext Transfer Protocol over Secure Socket Layer)
should be used for WBM communication between the browser and the
BSIP1. Using https encrypts the communication between the browser and the
WBM. It is suggested to use https mode.
Depending on the http access mode you have to use http:// or https:// mode
at the browser.
HTTPS Enabled = [ ] use http://{Server Ip IP VoIP (Infrastructure) Network}
HTTPS Enabled = [X] use
https://
{Server Ip IP VoIP (Infrastructure) Network}
Example: https://192.168.201.114
Tos Value
With the “TOS Value“ you can configure the prioritization of the IP packets via
TCP/IP (Layer3 ) according to DSCP. It is only used for the IP DSCP field for
VoIP Signalling (SIP) and VoIP data (RTP) packets towards the PBX (VoIP
Infrastructure Network).
Other IP packets e.g.
• WBM or SSH towards the VoIP Infrastructure network or
• packets between BSIP1 Only and BSIP1 IWU (DECT Network)
are NOT tagged with configured the DSCP value. (Default = “0“, i.e. no priori-
tization).
Using the dropdown you may select one of the pre-configured ToS values.
Cos Value
With the “CoS Value“ (decimal) you can configure the prioritization of the
ethernet packets via ethernet (Layer2) according to 802.1p. (Default = “0“, i.e.
no prioritization).
Using the dropdown you may select one of the pre-configured CoS values.
VLAN Id
The corresponding VLAN Id is configured here. If VLANs are used (value
unequal to "0"), the switch port connected with the BSIP IWU has to be confi-
gured to tag the ethernet frames.
If a value of zero (0) is configured here, the BSIP IWU will not tag the ethernet
frames. Otherwise, the frames are tagged according to their destination.
All frames inside the destinated VoIP (Infrastructure) network will be tagged
with the configured VLAN Id. All frames destinated to the DECT network will
be tagged with the VLAN Id configured at the DECT page.
Hint: The BSIP1 ethernet tagging feature is only activated for VLANId <> "0".