User's Manual

ManualsBrandsSiemens Canada Ltd. - Siemens Milltronics Process Instruments ManualsElectronicsSITRANS LR560 Level Probing Radar

Table Of Contents

Safety Notes
- Safety marking symbols
FCC Conformity
- US Installations only: Federal Communications Commission (FCC) rules
CE Electromagnetic Compatibility (EMC) Conformity
Industry Canada
The Manual
- Application Example
Technical Support
- Abbreviations and Identifications
SITRANS LR560 Overview
- Programming
  - Local Display Interface (LDI)
- Versions
- Applications
- Approvals and Certificates
Specifications
- Power
- Performance
- Interface
- Mechanical
- Environmental
- Process
- Approvals
- Programmer (infrared keypad)
- Dimensions
Installation
- Pressure Equipment Directive, PED, 97/23/EC
- Mounting location
  - Nozzle location
  - Aimer Adjustment
    - 3" flange 4 and 6" flange
- Air Purging System
  - Purge Connection
    - Purge airflow
- Removable Display
Wiring
- Power
- Connecting SITRANS LR560
  - Basic Configuration with Foundation Fieldbus (H1)
- Wiring Setups for hazardous area installations
  - Configuration with Foundation Fieldbus for hazardous areas
    - Configuration for hazardous areas (continued)
  - Instructions specific to hazardous area installations
    - (Reference European ATEX Directive 94/9/EC, Annex II, 1.0.6)
    - Special Conditions for Safe Use
Local Operation
- Activating SITRANS LR560
- To configure a device via the local user interface
  - Quick Start Wizard via the LDI push buttons
    - To add or delete digits using the push buttons:
    - To modify a text string:
  - Quick Start Wizard via the handheld programmer
- Requesting an Echo Profile
- Device Address
- Level application example
Operating via AMS Device Manager
- Functions in AMS Device Manager
  - Key Features of AMS Device Manager version 9.0.
  - Block location of features
- Programming via AMS Device Manager
- Adding a new device
  - Electronic Device Description (EDD)
- Startup
- Configuring a new device
  - Quick Start Wizard via AMS Device Manager
    - Quick Start Wizard steps
- Changing Block Modes
  - To change Resource Block mode
- Configure/Setup Parameters
- Password Protection
  - Login types
  - User Manager utility
    - To configure a new user/edit existing user:
AMS Menu Structure
Parameter Reference
- 1. Quick Start
- 2. Setup
- 3. Diagnostics
- 4. Service
- 5. Communication
- 6. Security
  - 6.1. Remote Access
    - 6.1.1. Remote Lockout
  - 6.2. Local Access
    - 6.2.1. Write Protection
    - 6.2.2. Local Operation
- 7. Language
Appendix A: Alphabetical Parameter List
Appendix B: Troubleshooting
- Communication Troubleshooting
- Device Status Icons
- General Fault Codes
- Operation Troubleshooting
Appendix C: Maintenance
- Unit Repair and Excluded Liability
Appendix D: Technical Reference
- Principles of Operation
  - Process Variables
- Echo Processing
  - Process Intelligence
  - Echo Selection
- Measurement Range
  - Near Range (2.4.1.)
  - Far Range (2.4.2.)
- Measurement Response
- Damping
- Loss of Echo (LOE)
  - Loss of Echo (LOE) Timer (2.3.4.)
- Temperature derating curves
  - Temperature De-Rating
Appendix E: Communications
- Foundation Fieldbus (FF) Protocol
- Field Communicator 375 (FC375)
Appendix F: Firmware Revision History
Glossary
Index
LCD menu structure

7ML19985LY01 SITRANS LR560 (FF) – INSTRUCTION MANUAL Page 45

mmmmm

AMS Device Manager

2) Master Reset

a) Navigate to Configure/Setup > Resource Block > Operation and click Methods

to open the dialog window.

b) In the General field, click Master Reset then click Next to perform a reset to

factory defaults. Click Next to accept the default reset to Factory Defaults.

c) Click FINISH, then scan the device (see step 3).

After a master reset is performed, the device will stop measuring, the Resource and Level

Transducer Blocks will go to Out of Service, and the LCD will display the Quick Start

Wizard until the device is configured.

3) Scan Device

Scan Device uploads parameters from the device to AMS Device Manager. This

synchronizes parameters between the device and AMS.

a) From the menu bar, open the pull-down menu Actions – Scan Device.

b) If you are adding a new device, configure the device via the Quick Start wizard.

Notes:

• We recommend performing a Master Reset before configuring a new device.

• RESOURCE and LTB Blocks must be in Out of Service Mode before a Master Reset

can be performed.

Master Reset