User's Manual

ManualsBrandsSiemens Canada Ltd. - Siemens Milltronics Process Instruments ManualsElectronicsSITRANS LR 250 TANK LEVEL PROBING RADAR

Table Of Contents

SITRANS LR250 (PROFIBUS PA)
Legal information
Table of contents
1 Introduction
- 1.1 The manual
- 1.2 Firmware revision history
2 Safety notes
- 2.1 Safety marking symbols
- 2.2 FCC Conformity
- 2.3 CE Electromagnetic Compatibility (EMC) Conformity
3 Description
- 3.1 SITRANS LR250 overview
- 3.2 Programming
- 3.3 Applications
- 3.4 Approvals and certificates
4 Installing/mounting
- 4.1 Pressure applications
  - 4.1.1 Pressure Equipment Directive, PED, 97/23/EC
- 4.2 Mounting location
- 4.3 Installation instructions
- 4.4 Flange bolting, Flanged encapsulated antenna only
5 Connecting
- 5.1 Power
- 5.2 Connecting SITRANS LR250
  - 5.2.1 Basic PLC configuration with PROFIBUS PA
- 5.3 Wiring setups for hazardous area installations
- 5.4 Instructions specific to hazardous area installations
6 Commissioning
- 6.1 Operating via the handheld programmer
- 6.2 Application examples
7 Remote operation
- 7.1 Operating via SIMATIC PDM
- 7.2 Operating via FDT
8 Parameter reference
- 8.1 Alphabetical parameter list
9 Service and maintenance
- 9.1 Maintenance
- 9.2 Unit repair and excluded liability
- 9.3 Part replacement
10 Diagnosing and troubleshooting
- 10.1 Device status icons
- 10.2 General fault codes
- 10.3 Operation troubleshooting
11 Technical data
- 11.1 Power
- 11.2 Performance
- 11.3 Interface
- 11.4 Mechanical
- 11.5 Environmental
- 11.6 Process
- 11.7 Approvals
- 11.8 Programmer (infrared keypad)
12 Dimension drawings
- 12.1 Threaded horn antenna
- 12.2 Threaded horn antenna with extension
- 12.3 Flanged horn antenna
- 12.4 Flanged horn antenna with extension
- 12.5 Flanged encapsulated antenna (2"/DN50/50A sizes only)
- 12.6 Flanged encapsulated antenna (3"/DN80/80A sizes and larger)
- 12.7 Threaded PVDF antenna
- 12.8 Threaded connection markings
- 12.9 Raised-Face flange per EN 1092-1 for flanged horn antenna
- 12.10 Raised-Face flange per EN 1092-1 for flanged encapsulated antenna
- 12.11 Flat-Face flange
- 12.12 Process connection tag (pressure rated versions)
A Appendix A: Technical reference
- A.1 Principles of operation
- A.2 Echo processing
- A.3 Maximum Process Temperature Chart
- A.4 Process Pressure/Temperature Derating Curves
B Appendix B: PROFIBUS PA profile structure
- B.1 PROFIBUS Level Device Design
- B.2 Block Model
C Appendix C: Communications via PROFIBUS
- C.1 Device configuration
  - C.1.1 SIMATIC PDM
  - C.1.1.1 Electronic Device Description
- C.2 Network configuration
  - C.2.1 The GSD file
- C.3 Bus termination
- C.4 Power demands
- C.5 PROFIBUS address
- C.6 Operating as a profile device
  - C.6.1 Configuring a new device
  - C.6.2 Configuring PROFIBUS PA with an S7-300/ 400 PLC
- C.7 Cyclic versus acyclic data
  - C.7.1 Cyclic data
- C.8 Status byte
- C.9 Condensed status
- C.10 Diagnostics
D Appendix D: Certificates and Support
- D.1 Certificates
- D.2 Technical support
13 List of abbreviations
14 LCD menu structure
Glossary
Index

Remote operation

7.1 Operating via SIMATIC PDM

SITRANS LR250 (PROFIBUS PA)

Operating Instructions, 01/2014, A5E32221386-AB

7.1.5

Parameters accessed via pull-down menus

Click on

Device

View

to open the associated pull-down menus.

Pull-down menus

Device menus

View menus

Communication path

Process Variables (Page 83)

Download to device

Upload to PC/PG

Update Diagnostic Status

Device Diagnostics

Toolbar

Status bar

Wizard - Quick Start (Page 62)

Update

Echo Profile Utilities (Page 69)

Maintenance (Page 77)

Acknowledge Faults (Page 78)

Wear (Page 78)

Simulation (Page 79)

Write Locking (Page 81)

Master Reset (Page 82)

7.1.5.1

Echo profile utilities

Open the menu

Device – Echo Profile Utilities

and click on the appropriate tab for easy access

to:

● Echo profile (Page 70)

● View Saved Echo Profiles (Page 71)

● TVT Shaper (Page 72)

● Auto False Echo Suppression (Page 73)

● Echo Setup (Page 76)