manual

 B1.ACPowerSocket
 B2.SerialPort(Optional)
 B3.S/PDIFOutPort
 B4.DVI-IPort
 B5.HDMIPort
 B6.eSATA&USB2.0Ports
 B7.USB3.0Ports
 B8.ClearCMOSButton
 B9.FrontSpeakerOut(L/R)Port
B10.SideSpeakerOut(L/R)Port
B11.RealSpeakerOut(L/R)Port
B12.Center/Subwoofer
  SpeakerOutPort
B13.Line-InPort
B14.LAN&USB2.0Ports
B15.WirelessLANPerforation 
  (Optional)
12. Fasten the Smart Fan
to the chassis with the
4 thumbscrews.
A. Begin Installation
1. Unscrew 3 thumbscrews of the chassis cover.
2. Slide the cover backwards and upwards.
3. Unfasten the rack mount screws and remove the rack.
B. CPU and ICE Installation
For safety reasons, please ensure that the power cord is
disconnected before opening the case.
1. Unfasten the ICE fan thumbscrews on the back of the chassis.
2. Unfasten the four ICE module attachment screws and unplug the fan
connector.
3. Remove the ICE module from the chassis and put it aside.
1. Unlock the DIMM latch.
2. Align the memory module's cutout with the DIMM slot notch.
Slide the memory module into the DIMM slot.
C. Memory module Installation
3. Check that the latches are closed, and the memory module is firmly installed.
E. Peripheral Installation
1. Unfasten expansion slot bracket screws.
Remove the back panel bracket and put the bracket aside.
F. Accessories Installation
2. Install the PCIe x4 / PCIe x16 card into the PCIe x4 / PCIe x16 slots.
3. Secure the bracket.
G. Complete
Please press "Del" key while booting to enter BIOS and load the
optimised BIOS settings.
Fan Connector
The maximum size acceptable for display cards is
267mm x 98mm x 34.6mm.
1. Replace the cover and refasten the thumbscrews.
2. Complete.
This 1155 pin socket is fragile and easily damaged. Always use
extreme care when installing a CPU and limit the number of times
that you remove or change the CPU. Before installing the CPU,
make sure to turn off the computer and unplug the power cord
from the power outlet to prevent damage to the CPU.
VGACardPCB
Chassis
Cover
5mm
34.6mm
5. Connect the Serial ATA and power cables to the optical drive.
Make sure that the motherboard supports the memory.
It is recommended that memory of the same capacity, brand,
speed,and chips are used.
(Go to Shuttle's website for the latest memory support list.)
Memory modules have a foolproof design. A memory module can
be installed in only one direction. If you are unable to insert the
memory, switch the direction.
GuidelinesforMemoryConguration

Before installing DIMMs, read and follow these guidelines for memory
configuration.
Installingamemorymodule
DDR3 and DDR2 DIMMs are not compatible to each other or DDR DIMMs.
Be sure to install DDR3 DIMMs on this motherboard. Follow the steps below
to correctly install your memory modules in the memory sockets.
Repeat the above steps to install additional memory modules,
if required.
Cutout
Latch
Latch
Notch
DDR3 240-pin 1.5V
48*2=96 pin
72*2=144 pin
A DDR3 memory module has a cutout, so it can only fit in one direction.
10. Screw the ICE module to the mainboard. Note to press down on the
opposite diagonal corner while tightening each screw.
11. Connect the fan connector.
4. First unlock. Press
A
with your thumb, then move it to
B
until it is
released from the retention tab and raise the socket lever.
Follow the steps below to correctly install the CPU into the
motherboard CPU socket.
Please be aware of the CPU orientation, DO NOT force the CPU into
the socket to avoid bending of pins on the socket and damage of CPU!
6. Orientate the CPU and socket, you may align the CPU notches with the
socket alignment keys. Make sure the CPU is perfectly horizontal, insert
the CPU into the socket.
DO NOT touch socket contacts. To protect the CPU socket, always
replace the protective socket cover when the CPU is not installed.
Socket
1155
CPU
Triangle Pin1
Marking
on the CPU
2
1
3
L
The product’s colour and specification will depend on the actual shipping product.
Fan Connector
4. Connect the Serial ATA and power cables to the HDD.
2. Place the HDD and optical drive in the rack and secure with screws
from the side.
3. Place the rack in the chassis and refasten the rack.
1. Loosen the purse lock and separate the Serial ATA and power cables.
7. Close the metal load plate, lower the CPU socket lever and lock in place.
8. Spread thermal paste evenly on the CPU surface.
5. Lift the metal load plate on the CPU socket.
Metal load
plate
Dual-ChannelmodePopulationRule

In Dual-Channel mode, the memory modules can transmit and receive
data with two data bus lines simultaneously. Enabling Dual-Channel
mode can enhance the system performance. The following illustrations
explain the population rules for Dual-Channel mode.
DIMM1(Red),Installed
DIMM2(Yellow),Installed
DIMM3(Red),Installed
DIMM4(Yellow),Installed
A
B
PCIex16slot
PCIex4slot
SerialATACable
SerialATAPowerCable
SerialATACable
SerialATAPowerCable
SerialATAHDD
SerialATAOpticalDrive
PCIex16/PCIex4slots
4x240pinsDDR3DIMMSlots
CPUFANConnector-FAN1
SideSpeakerOut/
RealSpeakerOut
/Center/
SubwooferSpeakerOutPort
FrontSpeakerOut
/Line-InPorts
2xUSB2.0&1xLANPorts
ATXPowerConnector-PWR1
ATXPowerConnector-ATX1
SATA2.0Connector

-SATA3,SATRA4
FrontAudioHeader-JP5
USBHeader-USB2
J6
J3
PowerHeader-JP3
LGA1155
J9
J5
J1
CPUFANConnector-FAN2
J2
HDMI&DVI-IPort
OnePCIex4Slot
OnePCIex16Slot
SATA3.0Connector

-SATA1,SATA2
2xUSB3.0Ports
ClearCMOSButton
LPCHeader-JP1
USB3.0Header-JP4
J4
J8
9. Tear off the protective membrane from the bottom of ICE module.
Remove the protective socket mylar from the CPU socket.
Remove the
protective
membrane
1=Ground
2=VCC
3=SPDIFO
J6
 CPUFanConnectors
J5
 AUXINConnector
1=AUX-IN – Left
2=Ground
3=Ground
4=AUX-IN – Right
4321
J7
 USBHeader(USB1,USB2)
SPEED_SENSE
PWM_CTRL
+12V
Ground
FAN1/FAN2
123
1=5V_USB 2=5V_USB
3=USB A- 4=USB B-
5=USB A+ 6=USB B+
7=GND 8=GND
9=NA 10=NULL
97531
108642
J1
S/PDIFOutPutConnector(JP2)
J4
 PowerHeader(JP3)
1=+HD_LED 2=PWR_LED
3=-HD_LED 4=
GND
5=RST_SW 6=PWR_SW
7=GND 8=GND
9=NULL 10=NA
97531
108642
J10
FrontAudioHeader(JP5)
1=MIC_L 2=GND
3=MIC_R 4=Front_Detect
5=LINE_R 6=Mic_detect
7=sense 8=NA
9=LINE_L 10=Line_Detect
97531
108642
J9
 USB3.0Header(JP4)
1=5VCC 2=A_RX_N
5=A_TX_N 6=
A_TX_P
9=A_Data_P 10=OC
13=Ground 14=B_TX_P
17=B_RX_P 18=B_RX_N
J7
DIMM1(Red),Empty
DIMM2(Yellow),Installed
DIMM3(Red),Empty
DIMM4(Yellow),Installed
MotherboardIllustration
BackPanel
SZ77R5QuickGuide【English】
FrontPanel
JumperSettings
3=A_RX_P 4=Ground
7=Ground 8=
A_Data_N
11=B_Data_P 12=B_Data_N
15=B_TX_N 16=Ground
19=5VCC 20=NA
1  2  3  4  5  6  7  8  9  10
11 12 13 14 15 16 17 18 19 20
J3
 COMHeader(COM1)
1=DCD 2=RXD
3=TXD 4=
DTR
5=Ground 6=DSR
7=RTS 8=CTS
9=Ring 10=NA
97531
108642
J8
 LPCHeader(JP1)
1=+12V 2=5V
5=CLK_48M 6=
CLK_33M
9=LAD3 10=LAD2
13=Ring 14=LDRQ0
17=LAD0 18=+3.3V
3=5VSB 4=SERIRQ
7=SIO_RST 8=
LFRAME
11=-12V 12=3VSB
15=SIO_PME 16=LAD1
19=GND 20=NA
1  2  3  4  5  6  7  8  9  10
11 12 13 14 15 16 17 18 19 20
1=5V
2=NA
3=Ground
4=GPIO1
5=GPIO2
J2
CIRHeader(JP6)
1  2  3  4  5
B10
B9
B11
B13
B15
B6
B3
B14
B7
B12
B15
B4
B5
B8
B2
B15
B1
2xUSB2.0&eSATAPorts
COMHeader-COM1
CIRHeader-JP6
Intel
®
64Chipset
USBHeader-USB1
AUX_INConnector
S/PDIFOutPut
Connector-JP2
J6
J7
J10
Please do not apply excess amount of thermal paste.
Thermal Paste
application area
ConnecttheSerialATA
Cabletomotherboard.
1. Install the Mini PCIe card into the Mini PCIe slot / mSATA Slot and affix it
with screws.
D. Mini PCIe card Installation
F7
F1
F5
F2
F6
F8 F9
F11
F10
F3
F4
MiniPCIeSlot
MiniPCIeslotwith
mSATAsupport
62R-SZ77R0-0601 SZ77R5
English.Spanish.Korean.
Traditional Chinese.Japanese.
French. German Quick Guide
53R-SZ77R3-2001
 F1. 5.25”Bay
 F2. 3.5”Bay
 F3. EjectButton
 F4. OpenDoor
 F5. PowerSwitch&PowerLED
 F6. HDDLED
 F7. USB3.0Ports
 F8. USB2.0Port
 F9. MicIn
 F10.Headphone
 F11.USB2.0Port&FastCharger
SafetyInformation
 ReadthefollowingprecautionsbeforesettingupaShuttleXPC.
Laser compliance statement
TheopticaldiscdriveinthisPCisalaserproduct.

Thedrive'sclassicationlabelislocatedonthedrive.
CLASS 1 LASER PRODUCT
ＥAUTION INVISIBLELASERRADIATIONWHENOPEN.
 AVOIDEXPOSURETOBEAM.
CAUTION
Incorrectlyreplacingthebatterymaydamagethiscomputer.
ReplaceonlywiththesameorequivalentasrecommendedbyShuttle.
Disposalofusedbatteriesaccordingtothemanufacturer'sinstructions.
A
B
1
2