User's Manual
Product
Specifications
Page
9
|
28
August
2013
Mena Computers
Wageningselaan 46 -A
3903 LA Veenendaal
|
The Netherlands
Tel
.
+31 (0) 318 518 720
sales@shuttleshop.nl
w w w . s h u t t l e s h o p . nl
Reference values and
compliance
Tran
sfer
Speed
[1]
Read data
- from
NAS
to
w
o
r
k
station:
up to 100 MB/s
Write
data
- from
workstation
to
NAS:
up to 70
M
B
/s
Maximum
number
of
concurrent connections:
256
Power
Con-
sumption
[1]
Power off:
0.35W
Power
saving mode (suspend):
9.6 W
Normal
operating
(no
hard
d
i
sk
access):
19 W
Operating temperature range: 5~40
°C
Relative humidity
range: 10~90%
(
n
on-con
den
sin
g)
Operating
temperatire
ran
g
e
CE
Compl
i
a
n
ce
This
device
is
classed
as
a
techn
i
cal
information equipment
(ITE)
in class
B
and
is
intended
for
use
in
livin
g
room
and
office. The CE
and
WEEE
marks
approve the
conformity
by the
EU-guidelines:
•
EMC
-
guideline 2004/108/EC,
Directive on
Electromagnetic
Compatib
ility
•
LVD
-
guideline 2006/95/EC,
Direct
i
ve
on Low
Voltage
•
ErP Lot6 -
guideline 2009/125/EC,
Direct
i
ve
on
ecoconception
of
E
nergy
related
Products
•
RoHS -
guideline 2002/95/EC,
Directive on Restriction of
Hazardous
Substances
•
WEEE
-
guideline 2002/96/EC,
Directive on The Waste
Electrical and
Electronic
Equipmen
t
Other
•
CB (IEC
60950-1:2005
(2nd Edition)
•
F
CC
Footnotes:
[1]
depending
on the test
e
n
vironment
[2]
the
threshold temperatures are subject
to
change
by
f
i
rmware
update.
The KD20's
threshold temperature
refers to the "Current
internal temperature" provided
by the
SMART
mon
i
torin
g
system.
This
temperature
may
be much higher than
the
"operating/ambient temperature"
that is also
mentioned
in
the
hard
disk
specification.
The KD20 only
supports hard
disks with
SMART
mon
i
torin
g
system
and
te
mperature
sensor which all
available
SATA
hard
disks
should support.
[3]
Picture Transfer
Protocol
(PTP)
- allows the transfer of
images
from digital
cameras
to
computers and
other
peripheral devices
without the
need
of
additional device
drivers.
Modern
digital
cameras
usually
support
this
protocol.
[4]
The
single
disk
expansion
fun
c
tion
is
designed
to allow you to
create additional storage space
without
changing
your
current single
disk
mode.
The
second
disk is then
recognized
as
"external
drive".
Please
refer
chapter
"
S
torage
M
a
n
agem
e
n
t
"
in the
manual
for further in
formation
.
[5]
You
can enable
the
W
a
ke
on
LAN
fun
c
tion
in
W
e
b
User
Interface:
Settings -
General
-
E
n
able
W
a
ke-On
-
LAN.
After
Wake on
LAN is
enabled
for your
OMNINAS,
you
can
switch off the
OMNINAS
and
turn on over the
n
e
twork by
usin
g
a
W
O
L
(
W
ake
on
LAN)
application.
For
proper function, please
do not interrupt the
power
supply from the
OMNINAS.
You
will
find the
MAC
address
on the
bottom
of the
OMNINAS
device.