Performance Gear Series Wireless
English Shure Performance Gear Wireless Designed especially for performers who manage their own sound, Shure Performance Gear professional audio products deliver legendary Shure sound quality, stage-proven durability and hasslefree setup for worry-free performance. Performance Gear Wireless systems are available in a variety of configurations - for handheld, guitar, headset and presentation applications.
English PG4 Receiver Features Figure 1. Front Panel audio LED Channel Display Indicates strength of incoming audio signal: green for normal, amber for strong, red for peak. See “System Setup” on page 6. ready LED Green LED indicates system is ready for use. channel button Press and hold to change the frequency channel. Figure 2.
English PG2 Handheld Transmitter Figure 3. Power/Mute Button Power/Mute LED (See LED status below) Channel Display (Display turns off after 10 seconds to conserve battery) Channel Button Battery Cover — Twist counter-clockwise to remove. Battery Compartment LED Status Signifies Green Ready Amber Mute is on Red Battery is low Flashing Red on startup Battery dead (must be replaced for transmitter to operate).
English PG1 Bodypack Transmitter Figure 6. Figure 5. Battery Cover, pinch sides to fold open 4-Pin Microphone Input Jack Power/Mute Button. Press and hold to turn on/off. Press and release to mute/unmute. Power/Mute LED (see LED Status below) Antenna Channel Display Channel Button Gain Switch 9V Battery compartment Battery Cover. Pinch sides to fold open. LED Status Signifies...
English System Setup Single Receiver Setup In any wireless setup, each transmitter and receiver pair must be tuned to the same frequency, or channel. Follow these steps to set the transmitter and receiver to the same channel: 1. 2. 3. 4. 5. 6. 7. 8. Plug in the receiver to turn power on. Turn transmitter power off. Press and hold the channel button on the receiver for about one second to enter select mode. Release the button as soon as the display begins flashing.
English Multiple System Setup To set up multiple systems, repeat the previous steps for each transmitter and receiver pair. Once transmitters have been set, leave them on. Be sure to set each transmitter and receiver pair to a different frequency. For information about frequencies and compatibility, refer to the guide below. TLPW Frequency and Channel Guide In each group, channels 1,3,5,7 and 9 are a compatible set and channels 2,4,6,8 and 0 are a compatible set.
Troubleshooting Issue LED Status Solution No sound or faint sound Transmitter Power/Mute LED on, receiver LEDs on • Perform transmitter setup (see page 6). • Verify all sound system connections. • Adjust transmitter gain. Receiver Channel Display • Make sure AC adapter is securely plugged into electrical outlet and into POWER connector on rear panel of receiver . • Make sure AC electrical outlet works and is supplying proper voltage.
English Specifications System PG1 Bodypack Transmitter PG2 Handheld Transmitter ���� PG4 Receiver Working Range 75m (250 ft.) Note: actual range depends on RF signal absorption, reflection, and interference. Audio Frequency Response Minimum: 45 Hz. Maximum: 15 kHz (overall system frequency depends on microphone element). Total Harmonic Distortion 0.5%, typical Ref.
English Replacement Parts All Systems Microphone Stand Adapter (PGX2) WA371 System-Specific AC Adapter (120 VAC, 60 Hz) PS20 AC Adapter (230 VAC, 50/60 Hz, Europlug) PS20E AC Adapter (230 VAC, 50/60 Hz, UK) PS20UK AC Adapter (100 VAC, 50/60 Hz) PS20J AC Adapter (220 VAC, 50 Hz, China) PS20CHN PG58 Head with Grille RPW108 Belt Clip 44A8035 Universal Rack Tray URT 4-pin mini connector (TA4F) to 1/4” connector cable WA302 Optional 10
English Regulatory Information Regulatory Information for North America, Europe, and Australia PG1 & PG2 Transmitters: Certified to FCC Part 74 (FCC ID: “DD4PG1” and “DD4PG2”). Certified by IC in Canada under RSS-123 and RSS-102 (“IC: 616A-PG1” and “IC: 616A-PG2”). Meets the essential requirements of the European R&TTE Directive 99/5/EC (ETSI EN 300-422 Parts 1 & 2, EN 301 489 Parts 1 & 9) and are eligible to carry the CE marking.
SHURE Incorporated http://www.shure.com United States, Canada, Latin America, Caribbean: 5800 W. Touhy Avenue, Niles, IL 60714-4608, U.S.A. Phone: 847-600-2000 U.S.
