User's Manual
Table Of Contents
- Table of Contents
- AD4DDual Channel Receiver
- IMPORTANT SAFETY INSTRUCTIONS
- Australia Warning for Wireless
- AD4D Axient Digital Two-Channel Wireless Receiver
- Included Components
- Mounting Instructions
- Hardware
- Menus and Configuration
- Radio Frequency (RF) Settings
- Setting the RF Tuning Band
- IR Sync
- Setting the Frequency Manually
- Channel Scan and Group Scan
- Requesting a New Frequency from a Spectrum Manager
- Transmission Modes
- Assigning Transmitters to Transmitter Slots
- Interference Management
- Channel Quality Meter
- Frequency Diversity
- Antenna Bias
- RF Cascade Ports
- Firmware
- Audio Settings
- Networking
- Operation
- Troubleshooting
- Specifications
- System Specifications
- RF Carrier Frequency Range
- Working Range
- RF Tuning Step Size
- Channel-to-Channel Spacing
- Channel-to-Channel Spacing
- Image Rejection
- RF Sensitivity
- Latency Analog Output
- Audio Frequency Response
- Signal-to-Noise Ratio(Dynamic Range)
- Total Harmonic Distortion
- System Audio Polarity
- Operating Temperature Range
- Storage Temperature Range
- Audio Output
- Gain Adjustment Range
- Configuration
- Impedance
- Full Scale Output (200K Ω load)
- Mic/Line Switch
- Phantom Power Protection
- Dimensions
- Weight
- Housing
- Power Requirements
- Thermal Power Dissipation
- DC Power Requirements
- Network Interface
- Network Addressing Capability
- Maximum Cable Length
- Cascade Output
- Connector Type
- Configuration
- Impedance
- Insertion Loss
- RF Input
- Spurious Rejection
- Connector Type
- Impedance
- Bias Voltage
- RF Carrier Frequency Range model dependent
- Tables and Diagrams
- Receiver Frequency Bands
- Certifications
- Certifications
- Contact Customer Support
Shure Incorporated
5/41
•
•
•
•
•
•
•
•
•
•
◦
◦
•
•
•
•
•
•
•
•
WARNING: Voltages in this equipment are hazardous to life. No user-serviceable parts inside. Refer all servicing to qualified
service personnel. The safety certifications do not apply when the operating voltage is changed from the factory setting.
Australia Warning for Wireless
This device operates under an ACMA class licence and must comply with all the conditions of that licence including operating
frequencies. Before 31 December 2014, this device will comply if it is operated in the 520-820 MHz frequency band.
WARNING: After 31 December 2014, in order to comply, this device must not be operated in the 694-820 MHz band.
AD4D Axient Digital Two-Channel Wireless Receiver
The AD4D Axient Digital TwoChannel Wireless Receiver sets a new standard in transparent digital audio and maximum spec
tral efficiency. Groundbreaking performance features include wide tuning, low latency, and High Density (HD) mode, ensuring
solid performance in the most challenging RF environments. Networked control, AES3 and Dante output, and signal routing op
tions bring a new level of management and flexibility to your entire workflow. Compatible with all Axient Digital transmitters.
Features
Audio
60 dB of gain adjustment offers compatibility with a wide range of input sources
Dante networking for quick and easy channel management
Dante Browse feature for headphone monitoring of all Dante channels, including third party components
AES 256 encryption to protect audio channels
Automatic limiter function protects against signal clipping, allowing for higher gain settings and preventing unexpected sig
nal peaks
Front panel connection for headphones with adjustable volume
I/O
2 transformer-balanced XLR outputs
AES3 Digital output
2 transformer-balanced 1/4'' outputs
2 Dante-enabled Ethernet ports, 2 network control Ethernet ports with PoE
Split-Redundant mode: 2 ports of Ethernet, 2 ports of Dante
Switched mode: 4 ports of Ethernet, 4 ports of Dante
Locking AC power connection
AC power cascade to additional components
Optional DC module available to support redundant power
RF
True digital diversity reception per channel
Up to 210 MHz of tuning range
Frequency diversity with selection (bodypack) or combining (handheld)
Channel Quality meter displays signal-to-noise ratio of RF signal
Antenna cascade for 1 additional receiver
™